467073
84
Zoom out
Zoom in
Previous page
1/117
Next page
Page 20/53
2. CHARGE SETUP MENU FLOW
Warning: To high settings of charging voltage (Li-batteries), charging current (all types)
or delta peak sensitivity (NiMH/NiCd) batteries can cause explosion and fire!
2-1. CHARGE CURRENT
- Set charge currents. Follow the instruction of the battery. Graupner batteries
should be charged with 0.5-1C (f. e. 6N-4200 should be charged with 4.2A).
Transmitter batteries must be charge with less then 2A. Follow the instruction of
the transmitter battery and transmitter.
2-2. PEAK SENS
WARNING! To high settings of the delta peak sensitivity can cause explosion and fire.
- Only for NiCd/NiMH. Follow the instruction of your battery or start with 3mV/Cell.
- If battery is 6cells and 3mV/C is set, the charger should finish as 3mV * 6cell =
18mV.
- In case of NIMH battery, charge can be also finished with Zero-peak.
- Set bigger peak sens values if delta-peak often happens.
- "END:DELTA-PEAK " should be shown if charge is finished with delta-peak.
- "END:ZERO-PEAK should be shown if charge is finished with ZERO-peak.
2-3. PEAK DELAY
- This function is not to detect delta peak which could happen at the initial stage of
charging and which could happen due to the chemical reaction internal battery.
Normal settings are 3-5min.
2-4. TRICKLE
- This current is to compensate battery self discharge after NICD/NiMH fast charging.
- As for Lithium battery, CV ( constant voltage ) is activated instead of trickle charge.
2-5. CUT-TEMP
- Connect the temp sensor to battery pack and when it reaches the selected temp,
charging should stop. Normal settings are 35-50°C.
- This function is likely to be used more to prevent battery pack from being
overheating rather than normal charge completion.
2-6. MAX CAPACITY
- This is to set your wanted charge percentage against the selected battery capacity.
- Set half of the battery capacity ( 50% ) for the purpose of the battery storage. Set
120-125% for fully charging of high current NiCd/NiMH batteries and 100-105% for
charging LiPo-, LiIo-, LiFe- batteries and NiMH RTU (Ready to use) batteries.
- If battery capacity is 3000mAh and if you set 10% out of the total max capacity, the
charger should stop charging at 300mAh.
- If “OFF” is set, this max capacity function is not activated.
- If charging is finished with MAX CAPACITY, “END:CAPACITY should be shown.
84


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner ULTRA DUO PLUS 50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner ULTRA DUO PLUS 50 in the language / languages: German as an attachment in your email.

The manual is 3,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner ULTRA DUO PLUS 50

Graupner ULTRA DUO PLUS 50 User Manual - Dutch - 65 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info