747908
34
Zoom out
Zoom in
Previous page
1/48
Next page
34 / 48
S1024.mz32_V1.7_sh_en
Telemetry
The telemetry connecon between the transmier and receiver
takes place via the return channel of the HoTT receiver defined as
the main receiver. If more than one receiver is bound to a model
memory, the return channel will be by default the last bound receiver.
This assignment can be changed in the submenu “RF Setin the base
menu or at the special “Telemetry” menu.
Depending on the seng of the value field at the Tele. Cycle” the
transmission of telemetry data takes place aer each fourth data
packet. This also influences the reacon me to control inputs when
making seng changes at the ASCII menu when seng up for exam-
ple a flight controller using the wireless interface. The corresponding
delay does not constute an error
Note
Sensors must always be connected to the main receiver, since only
the return channel of this receiver is evaluated by the transmier.
Aenon
Programming on the model or on sensors must not be carried out
during ongoing model operaon and only when the engine/motor
is switched off!
Select Rx
Up to four receivers can be bound to a model memory in the sub-
menu “RF Set” of the basic menu. However, a telemetry connecon
can only ever be established to one of these four receivers which as
standard is always the last bound receiver. All sensors are to be con-
nected to the receiver that is designated as the receiver from which
we expect to receive telemetry informaon from. This is important
in a mul receiver configuraon and therefore will require proper
planning as to the locaon of the receiver which should be close to
where the telemetry sensors are installed.
In the
“RF Set” menu the receiver that has the “T.Sel” field checked
is the receiver that provides telemetric informaon to the transmit-
ter
Viewing telemetric informaon or sengs from addional receivers
bound to the model can be done by tapping on the “RX Select” field
which will show an list with all acve receivers to pick from.
Aenon
This also changes the assignment in the column
"T. sel." of the submenu "RF Set". Aer compleng the adjustments,
it may be necessary to restore the original assignment!
34


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MZ-32 HoTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MZ-32 HoTT in the language / languages: English as an attachment in your email.

The manual is 26,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MZ-32 HoTT

Graupner MZ-32 HoTT User Manual - German - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info