30127
11
Zoom out
Zoom in
Previous page
1/48
Next page
9. The left side of the right-hand assembly has a metal
strip which provides the ratched friction action. This
is held in place by two screws. Undo the screws and
transfer the metal strip to the left-hand assembly.
10. The mechanical conversion is now completed; check
the stick actions are as required and reassemble the
transmitter by reversing the above process, not for-
getting to plug in the multipin connectors.
Frequency notes
The mx-12 can transmit in either Pulse Code Modulation
(PCM) or Pulse Position Modulation (PPM, commonly
referred to as FM):
Be certain to observe the following guidelines:
Do not operate your transmitter when another transmit-
ter is using the dame frequency, regardless of whether
the second transmitter is PCM, PPM (FM) or AM. You
can never operate two transmitters on the same fre-
quency simultaneously without causinf interference.
Direct servo control 11
Direct servo control (DSC)
For proper DSC hook-up and operation:
1. Leave the transmitter power switch in the OFF posi-
tion. The transmitter will not transmit any radio fre-
quency (RF) in this position.
2. Plug the (supplied) DSC cord into the DSC port in
the rear of the transmitter.
3. The encoder section of the transmitter will now be
operational and the LCD display will be lit.
4. Plug the other end of the DSC Cord into the receiver
charge receptacle. Turn the switch harness to the ON
position.
Note: When you install the charging jack, be sure to
hook the charging jack receptable securely into
the switch harness charge cord.
Why you should use the DSC function:
1. The DSC enables you to check the control surfaces
of your aircraft without drawing the fully operational
200mAh from your transmitter battery pack. Instead,
you will only draw approximately 70mAh when using
the DSC function.
2. The DSC function allows you to make final adjust-
ments to your airplane without transmitting any radio
signals. Therefore, if another pilot is flying on your
frequency, you can still adjust your aircraft and not
interfere with the other pilot`s aircraft.
Note: This function is for bench-checking your airplane
only.
TO BATT TERMINAL
SW HARNESS G
(OPTION)
DSC-CORD
Best.-Nr. 4178.1
V-CORD
Best.-Nr. 3936.11
BATTERY
BATTERY
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MX12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX12 in the language / languages: English as an attachment in your email.

The manual is 3,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX12

Graupner MX12 User Manual - English, German - 144 pages

Graupner MX12 User Manual - Dutch - 47 pages

Graupner MX12 User Manual - French - 144 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info