30127
56
Zoom out
Zoom in
Previous page
1/144
Next page
8 Charging the transmitter battery
Charging the transmitter battery
Charging the transmitter battery
The rechargeable transmitter battery can be charged
via the charge socket fitted to the side of the case.
The transmitter must be switched „OFF for the whole
period of the charge process. Never switch on the
transmitter when it is still connected to the charger;
even a very brief interruption in the charge process
can cause the charge voltage to rise to the point where
the transmitter is immediately damaged by the excess
voltage. Alternatively the interruption may trigger a new
charge cycle, which means that the battery will possibly
be severely overcharged.
For this reason check carefully that all connectors
are secure, and making really good contact. Inter-
ruptions due to an intermittent contact, no matter
how brief, inevitably cause the charger to malfunc-
tion.
Polarity of the mx-12 charge socket
Commercially available battery charge leads produced
by other manufacturers are often made up with the op-
posite polarity. For this reason use genuine GRAUPNER
charge leads exclusively.
Charge current
To avoid damage to the transmitter the maximum charge
current should not exceed 500 mA (0.5 A) with the char-
ge circuit fuse out of circuit (not fitted); with the charge
circuit fuse in place: max. 1.5 A.
Notes on recharging transmitter batteries using an
automatic charger
· Observe the recommendations provided by the
charger manufacturer and the battery manufactu-
rer at all times.
· Carry out a series of test charges to ensure that
the automatic charge termination circuit works
correctly with your battery. This applies in parti-
cular if you are using an automatic charger desig-
ned for NiCd batteries to recharge the standard
NiMH battery. You may need to adjust the Delta-
Peak trigger voltage, if your charger provides this
option.
· The charge current must be set using the
charger’s „manual charge current select“ facility,
to ensure that the maximum charge current never
exceeds 1.5 A. Never allow the charger to set the
charge current automatically.
· Do not discharge the battery or carry out a
battery maintenance program via the integral
charge socket. The charge socket is not suitable
for this application.
· If you intend to charge the transmitter battery at
a current higher than 1.5 A, the battery must be
removed beforehand, otherwise the transmitter
could be damaged through overheating.
Standard chargers
Order-No. 6422 Minilader 2
Order-No. 6427 Multilader 3
Order-No. 6426 Multilader 6E*
Order-No. 6428 Turbomat 6 Plus*
Order-No. 6429 Turbomat 7 Plus*
Automatic chargers with special NiMH charge
programs
Order-No. 6419 Ultramat 5*, **
Order-No. 6410 Ultramat 10*
Order-No. 6412 Ultramat 12*, **
Order-No. 6417 Ultramat 25*, **
Order-No. 6416 Ultra Duo Plus 30*, **
* To recharge the mx-12 system you will also need the transmitter
charge lead, Order No. 3022, and the receiver battery charge lead,
Order No. 3021.
** 12 V power source required.
56


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MX12 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX12 in the language / languages: English, German, French as an attachment in your email.

The manual is 15,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX12

Graupner MX12 User Manual - English - 48 pages

Graupner MX12 User Manual - Dutch - 47 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info