467107
166
Zoom out
Zoom in
Previous page
1/200
Next page
166
Programming example - fixed-wing model
First steps in programming a new model
Example: non-powered fixed-wing model aircraft
When programming a new model you should start by
activating the …
“select model” sub-menu (page 70)
… in the “Model memory menu. Use the arrow buttons
 of the left or right-hand touch-key to select a free
model memory …
03
04
05

free

02
01
06
R08

free


free


free


free

… then touch the central SET button of the right-hand
touch-key. You are now immediately requested to select
the type of model you wish to program.
Sel model type
( empty mod mem )
Since in this example we are setting up a fixed-wing
model, we simply confirm the fixed-wing model symbol
with a brief press on the central SET button of the right-
hand touch-key; the screen now reverts to the basic
display.
Notes:
Naturally you can also use the pre-defined model •
memory 01 for programming your first model; this is
the “fixed-wing model” type by default.
Once you have called up the “Model select” option it •
is not possible to interrupt the process, i. e. you must
choose one or other model type. Even if you switch
off the transmitter at this point, you cannot avoid this
select procedure. However, if you make a mistake
you can always correct it simply by erasing the mod-
el memory.
If the battery voltage is too low, you will not be able •
to change model memories for safety reasons. The
screen then displays an appropriate message:
not possible now
voltage too low
Once you have overcome this initial hurdle, you may
need to bind the receiver installed in the model to this
model memory in the …
“Base settings” menu (pages 74 … 81)
This is accomplished by moving to the “rx bind line:
phase 3
phase 4 landing
speed
–––
receiv out
rx bind
–––
phase 2 takeoff
–––
–––
Note:
When you confirm the model selection the following
message appears in the basic display for a few seconds:
BIND N/A
OK
If you confirm your choice by briefly pressing the SET
button of the right-hand touch-key, you automatically
move to this line:
In this line you trigger the bind process between model
memory and receiver, as described in detail on pages
80. Without this step you cannot address the receiver.
The next step is to press the arrow button of the
left-hand or right-hand four-way touch-key to move up
into the first line, where you can start the actual model
programming in the mod name line:
mod name
stick mode
CH8 delay
motor at C1
1
yes
no
tail type normal
At this point you can enter the Model name” by touch-
ing the central SET button of the right-hand touch-key in
order to move to the character table:
0123456789
PQRSTUVWXYZ
model name
?
:
;
ABCDEFGHIJKLMNO
GRAUB
You should also check the settings for “Stick mode and
Motor at Ch 1 and change them if necessary:
“none”:•
The brake system is “retracted” at the forward posi-
tion of the throttle / brake stick; the “Ch8 delayed” op-
tion and the “Brake NN*” mixers in the Wing mi-
xers menu are activated.
In the “Aileron / flap” line of the “Basic settings
menu you can select “1AIL”, “2AIL and “1/2AIL
* NN = Nomen Nominandum (name to be stated)
166


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MX-16 HoTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX-16 HoTT in the language / languages: English as an attachment in your email.

The manual is 4,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX-16 HoTT

Graupner MX-16 HoTT User Manual - Dutch - 188 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info