467107
22
Zoom out
Zoom in
Previous page
1/200
Next page
22
Description of transmitter
PUPIL
#11
0:01h
stop
flt
DSC
0:00
0:00
5.6V
HoTT
The transmitter is now ready for use.
In contrast, when the mx-16 HoTT is used in
Teacher mode, the transmitter must be switched on
before the appropriate cable is plugged in.
Connect the other end of the connecting lead to the 3.
appropriate apparatus, taking into account the oper-
ating instructions supplied with that device.
Important:
Ensure that all connectors are firmly seated in
their sockets.
Note regarding flight simulators:
The range of flight simulators available commercially
is now very wide, and you may find that it is necessary
to swap over certain contacts at the barrel connector
or the DSC module. This work must be carried out by a
Graupner Service Centre.
DSC
Direct Servo Control
The original function of this socket was for “Direct Servo
Control”, and that’s why the abbreviation is still in use.
However, for technical reasons “direct servo control” is
no longer possible with the HoTT system using a diag-
nosis lead.
The mx-16 HoTT transmitter’s standard two-pole DSC
socket is now used as a Trainer (buddy box) socket
(Teacher or Pupil), and as an interface for flight simula-
tors.
For the DSC connection to work you must check the
following:
Carry out any adjustments required in the appropri-1.
ate menus:
See page 154 for information on setting up the mx-
16 HoTT transmitter to work as part of a Trainer sys-
tem.
ALWAYS2. leave the transmitter’s On / Off switch in
the “OFF position when using a flight simulator, and
when using the mx-16 HoTT transmitter as a Pu-
pil unit in a Trainer system, for only in this position is
the RF section of the transmitter module switched off
(no RF signal) even when the DSC lead is plugged
in. At the same time the transmitter’s current drain is
reduced slightly.
The central Status LED should now glow a con-
stant red, and the abbreviation “DSC” appears in the
transmitter’s base display on the left, below the mod-
el number. At the same time the display of telemetry
symbols is suppressed:
Data storage
Card slot
micro-SD and micro-SDHC
When you switch off the mx-16 HoTT transmitter and
remove the battery compartment cover, you will see the
card slot for memory cards (of the micro-SD and micro-
SDHC type) in the right-hand side of the compartment:
In addition to the memory card supplied as standard, it
is possible to use any standard commercial micro-SD
memory card with a capacity of max. 2 GB, and any mi-
cro-SDHC card with a capacity of up to 32 GB. However,
the manufacturer recommends the use of memory cards
with capacities up to only 4 GB, as these are completely
adequate in all normal circumstances.
The memory cards for which the transmitter is intended
are familiar from their use in digital cameras and mobile
telephones. Place the card in the slot with the contacts
facing up, towards the back panel, and push it in until
it locks. When the battery has been installed and the
battery compartment closed, switching the transmitter
on causes a number of folders to be created on the
memory card. At the same time a stylised memory card
graphic appears in the base display to indicate that a
memory card is inserted.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MX-16 HoTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MX-16 HoTT in the language / languages: English as an attachment in your email.

The manual is 4,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MX-16 HoTT

Graupner MX-16 HoTT User Manual - Dutch - 188 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info