30117
86
Zoom out
Zoom in
Previous page
1/104
Next page
NAUTIC Expert Switch Function Modules
Only available in PPM Mode
86 Nautic
Optional Transmitter Module
16 Channel NAUTIC Expert Module
Part No. 4108
Up to two modules are connectable,
(Described on page 92)
Function Notes
The NAUTIC Expert module extends two
proportional channels to 16 signal
paths. All eight switches have a central
position, providing a genuine forwards–
stop–backwards function, if at the
receiver a switch module, Part No.
3754.1 or a Dual-Switch module Part No.
3754.2 is used. Of the 8 switches, 3
switches are sprung-off and 2 are
sprung-off in one direction. The
remaining 3 switches are intended for
forwards–stopbackwards functions
and are not self-centring.
Transmitter-laterally two modules with
altogether 32 switching functions can be
installed onto the module blow-out.
Fitting and connection to the mc-16/20
transmitter.
The modules are installed as shown in the
instructions on page 8/9 of this manual.
If the NAUTIC program in system menus
"NA7" and/or. "NA8" are switched to "ON"
(sees page 16), control paths 7 and/or 8
are automatically reserved for NAUTIC
modules dependent on the model type.
Model Type NAUTIC Channels
FL (Standard) 7 and 8
UN (Unifly) 7 and 8
Fb (F3B/Butterfly) 7 and 8
AC (Acrobatic) 7 only
HE (Helicopter) 7 only
The 5-pole connector of the module should
to be inserted, e.g. into socket "CH7", and
the 4-pole plug on the single-wire cable
connected to the "NAUTIC" socket on the
transmitter plate. If necessary a second
module can be connected to "CH8". The 4-
pole plug of the 2nd module is connected to
the module already inserted.
1. Servo reverse (page 21) NORM
2. Servo Neutral Point (page 21) 0
3. Servo Travel (page 21) ±146%
The setting is most easily done before
inserting the proportional or switch modules
(Part No. 4152 or 4151). During the servo
travel setting when the NAUTIC modules
are connected the display can flicker, which
makes reading the value more difficult.
4. AC: Code “AUTOLANDING”
if using ch 7 (page 57, 58) OFF
5. HE: Code “GYRO-CONTROL”
if using ch 7 (page 78, 79) OFF
6. HE: Code “SWASHPLATE TYPE”
if using ch 7 (page 66) Type 2 or 3
Both model types "AC" and "HE" can additionally, if necessary, use channel 5 as well as
channel 7 for the NAUTIC modules, under the following conditions:
86


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC16 in the language / languages: English as an attachment in your email.

The manual is 16,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC16

Graupner MC16 User Manual - German - 68 pages

Graupner MC16 User Manual - French - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info