30117
56
Zoom out
Zoom in
Previous page
1/104
Next page
Two Snap-Roll programs Automatic switching of control characteristics
(access via Set-Up Menu) (access via Set-Up Menu)
56 Fixed Wing Models
AUTOMATIC
MANOEUVRE
DUAL-RATE / EXPO-
AUTO-COUPLING
The switches to operate the Snap-Roll program must
be connected to socket 6 and/or 7 of the transmitter
board. This code allows the programming of aileron,
elevator and rudder positions, plus the pre-setting of
the throttle position. Two Snap-Roll programs are
available, i.e. Snap-Roll to left and right. To control
this function, momentary switches, part No. 4160.11,
4160.44 or kick-switch M4144, are needed to select
the Snap-Roll program “SR…”, and to turn off the
function immediately the switch is released.
The both programs differ as shown in the following
tables, The final program to be activated is always
indicated in the display.
Switch Display Function Ch
Socket 6 SR1 Throttle 1
SR2 Aileron 2
SR3 Elevator 3
SR4 Rudder 4
Socket 7 SRT Throttle 1
SRA Aileron 2
SRE Elevator 3
SRR Rudder 4
Note:
If two separate momentary switches are used, and both are turned
on together, the one connected to socket 7 has precedence.
Simultaneous activation of the Automatic Landing (code 22) using
switch 5, the Snap-Roll program will be inactive underneath the
switch point of the Automatic Landing
Consecutive presses of the CH SEL button moves
through the channels “SR2” through “SR4” and/or
“SRA, “SRE”, and “SRR”. The three channels can be
set independent of the position of switches 6 and 7,
or turned off using the CLEAR button. The first of the
codes “SR1” and/or “SRT” for the throttle control is
actually the fourth code that appears. The function
selection is changed by the CH SEL button, with the
CLEAR button cancelling a setting.
Now the servo setting for each sub-code “SR…” can
be set using the INC and/or DEC buttons in the
range 0 … ±125%
Momentary operation of switch 7 changes the
display between "SRA", "SRE", "SRR", "SRT".
The normal Dual-Rate (D/R) and Exponential
functions for channels channel 4 (rudder), see page
20, can be linked to the throttle control stick to
automatically switch between the two settings at
about 70% of full throttle.
Example:
0 … 70% throttle Rudder travel increased to
125%, with linear motion
(“LN”).
70% … 100% throttle Rudder travel decreased to
40% and exponential set to
50%.
The auto-coupling function will only operate if the
external switch at connection 2 is turned off.
In the D/R / Exponential setting, the selection for
rudder (channel 4) below 70% throttle travel is
indicated by “ch4”, with above 70% being shown by
“CH4”.
With the auto-coupling disabled, i.e. AT4 = "OF", the
D/R and Exponential for the rudder uses the normal
switching, as described on page 20
or
With the "AT4" function activated, the external D/R /
Exponential switch (connection 2) must be in the off
position for the auto-coupling to function. The
desired values are set using INC & DEC .
Note
:
The auto-coupling affects control function 4 in
accordance with the block diagram on page 52. Thus
to the left of the output point for mixers, it can
operate other control paths using the freely
programmable mixers A, B and C, and the same
from the right of the input point for mixers. For
example mix "A47" and a setting of 100% would give
similar auto-coupling effect to control paths 4 and 7.
56


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC16 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC16 in the language / languages: English as an attachment in your email.

The manual is 16,18 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC16

Graupner MC16 User Manual - German - 68 pages

Graupner MC16 User Manual - French - 11 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info