Manual Graupner MC 32 HOTT (page 329 of 345) (English)

467111

329

Zoom out

Zoom in

1/345

329

Programming examples - Helicopter models

built-in loudspeakers or the transmitter's headset con-

nector. The fourth line of this menu is used to record

the transmitter owner's name. Select the characters

for this from an extensive character list on the second

display screen, which can be reached via the



symbol with a brief tap on the centre SET key of the

right touch pad:

!"#$%&’()

Owners name

@ACDEFGHIJKLMNOPQRSTUVWXYZ[¥]^_

?+,–./0123456789:;

¢ÇüéâäàåçêëèïîìÄÅÉæÆôöòûùÖÜ

`abcdefghijklmnopqrstuvwxyz{|}~

H-J Sandb

The same applies to the pre-sets for "Modulation"

and "DSC Output" (page 94 and 100).

The pre-set for "Pitch min" (page 109) is a matter of

personal control habits. The pre-sets established here

for "Stick mode", "Modulation", "DSC Output" and

"Pitch forward/back" will be initially adopted when

a new model memory is created but they can also be

freely changed within a given model memory location

to any other available option.

The settings in the "Top/Bottom LCD Contrast" lines

determine the legibility of the given displays under

poor light conditions and the setting in the "Display

light" line determines how long display lighting re-

mains illuminated after the transmitter is switched on

without any actuation of a control afterward or after

the last control actuation. The selection of "yes/no" in

the "Power-on/off beep" line determines whether the

"recognition melody" is to sound when the transmit-

ter is switched off or on again. The "Battery type"

line speciﬁ es whether the transmitter is supplied with

current from a "NiMH or a “Lith." battery, and the

"Battery warning" line below it speciﬁ es the voltage

at which the transmitter's low-voltage warning should

trigger. Do not enter a value that is too low here, so

you have enough time to land your helicopter.

The setting made in the "Stick warning" line de-

termines how long the transmitter will wait after the

last actuation of an operating element before issuing

visual and acoustic warning signals to indicate it is

still switched on. Following the warning, you still have

about three minutes to actuate the transmitter so

the warning will abate. Otherwise the transmitter will

switch itself off when this time expires.

Later on, the ten “Own phase name” lines can be

used to create one’s own phase names if none of the

pre-set phase names appear appropriate.

The value set in the “Touch Sense” line is a matter of

adapting the transmitter to personal preferences.

In the “DATA SEL.” line you can specify which abuts

the two possible data logs to the located under the

left front cover Data socket. By default, it is the data

output on the Smart-Box, No. 33700, suitable “telem-

etry” protocol.

Finally, if you are using a Bluetooth headset, you

can bind and conﬁ gure it as described in the instruc-

tions supplied with the optional Bluetooth module, No.

33002.5; see the section entitled “BT Headset”.

Once these settings have been taken care of, com-

missioning continues with the menu …

Once these settings have been taken care of, com-

missioning continues with the menu …

"Model select" (page 73)

Use the selection keys to pick a free memory loca-

tion …

R16

 free

00:12h

 free

… and call it up with a brief tap on the centre SET key

of the right touch pad. In the display which then ap-

pears, use the  key of the left or right touch pad …

Select model type (free model memory)

… to select the "helicopter" model type. The display

immediately switches to the base screen if the selec-

tion is conﬁ rmed by a brief tap on the centre SET key

of the right touch pad.

Notes:

• If the "Select model type" option has been

opened, the process cannot be cancelled.

Even if you switch off the transmitter, this

selection must be made! In any case, you can

undo this by subsequently deleting the respective

model memory.

• If it appears the warning „Throttle too high“, it

can be deleted by pushing the default the throttle

limiter assigned to right side proportional rotary

slider on the back fence or moving the throttle /

pitch control stick of your transmitter to the idle or

Pitch min position.

• If battery voltage is too low, the model switchover

cannot be made due to reasons of safety. An

appropriate message will appear in the screen:

not possible now

voltage too low

Once this ﬁ rst hurdle is cleared, the connection of the

receiver built into the model at this model memory

must be made in the menu …

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC 32 HOTT in the language / languages: English as an attachment in your email.

The manual is 46,26 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC 32 HOTT

Graupner MC 32 HOTT User Manual - German - 320 pages

Graupner MC 32 HOTT User Manual - Dutch - 328 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Graupner MC 32 HOTT Manual

Product: