467111
307
Zoom out
Zoom in
Previous page
1/345
Next page
307
Programming examples - Parallel operating servos
This would be taken into account on the software side
in the pre-configuration of a corresponding mixer. You
can find this in the …
"Model type" (page 104)
In this menu, switch to the “Tail type” line using the
selection keys, activate the value field with a brief tap
on the centre SET key of the right key pad then select
the entry "2ELSv3+8":
Tail type
Motor on C1 none
Aileron/camber flaps 1 QR
M O D E L T Y P E
Brake Offset Input 1+100%
SEL
2 EL Sv 3+8
Then do the fine-tuning for travel of the two servos
"in the now familiar manner" in the »Servo adjust-
ment« menu.
Two rudders
We want to switch two rudders "in parallel". The sec-
ond rudder is located at the free receiver output 8.
Variant 1
The basis of this variant, as already mentioned the on
page 222, for the “normal” installation of the servos in
the fuselage and their connection to the rudder. That
is, both servos are parallel to each other vertically or
horizontally mounted in the fuselage, and both rud-
ders are either externally or internally connected in
the same direction of rotation to the servo arm.
In the following menu…
»Dual mixer« (page 222)
… select one of the dual-mixers and enter "8" and
"RU" in its left and centre value fields, as shown in the
figure:
Diff.
DUAL MIXER
Mixer 1
Mixer 2
8RU
Mixer 3
Mixer 4
?? ??
?? ??
?? ??
0%
0%
0%
0%
The same deflection " ", which would take place
through "Input 8" must not have an effect here. There-
fore, you should make absolutely sure in the …
»Control adjust« (page 118)
0% +100%I5
I6
I7
I8
Ty p SEL
+100%
0.0 0.0
– travel + –time+
0% +100%
+100%
0.0 0.0
0% +100%
+100%
0.0 0.0
0% +100%
+100%
0.0 0.0
GL
GL
GL
fr ---
fr
fr
fr
---
---
---
offset
GL
Normal
… menu, that "Input 8" "GL(obal)" is set to "free" so
the control function is separate from the control chan-
nel over all flight phases.
Alternatively, Input 8 can be set to "no control" in the
»Mix only channel« menu on a ight-phase inde-
pendent basis by setting Channel 8 to "MIXonly".
MIX ONLY CHANNEL
MIXonly
normal
1234567 8 9 10 11 12 13 14 15 16
Variant 2
This variant uses the …
»Free mixers« (beginning page 209)
… menu to set a "Tr RU 8". In the "Type" column,
select the setting "Tr" so that the rudder trimming af-
fects both rudder servos:
8
LinearMIX 1
type
RU
from – Begr. +
??
??
??
??
??
??
––––
LinearMIX 2
LinearMIX 3
LinearMIX 4
LinearMIX 5
to Adjust
––––
––––
??
??
––––
Tr
Afterwards, switch to the graphic screen and set a
symmetric mix of +100 %.
RU
Mix input Offset
8
Linear MIX 1
SYM ASY STO
0%
SET
+100% +100%
Here too, "Input 8" should also be programmed if
applicable, for all flight phases to "free" by way of the
»Control adjust« menu. However, control function
"8" can be separated from control channel "8" more
easily in the flight-phase independent »Mix only
channel« menu, page 221:
307


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC 32 HOTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC 32 HOTT in the language / languages: English as an attachment in your email.

The manual is 46,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC 32 HOTT

Graupner MC 32 HOTT User Manual - German - 320 pages

Graupner MC 32 HOTT User Manual - Dutch - 328 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info