467111
304
Zoom out
Zoom in
Previous page
1/345
Next page
304 Programming examples - Timer conrmation with control or switch
SEL
0%
0%
0%
C1
C2
C3
–––
C4
CONTROL SWITCH
Cnt. 1
free
–85%
STO
–––
–––
–––
SEL
C1
C2
C3
C4
free
free
Note:
Do not, however, set a switching point at a
transmitter control’s travel end-point, since
this makes reliable switching impossible.
Towards “full throttle” should now G1 be used here as
example, “closed” and again “open” under setpoint.
However, should this be the other way around the
case, go to the column on the right-hand SEL and
correct this by changing the shifting direction of “=>”
in “<=”.
To assign the newly created control switch the de-
sired timer now, you have to change a timer program-
ming according to example 4 and possibly according
to example 5 in the menu ...
»Phase timers« (page 168)
..., And select by the selection keys, the line of the
selected clock to, in this example “timer 1”:
SEL
0:00
0:00
0:00
Timer 1
Timer 2
Timer 3
–––
Lap cnt./timetab
0:00
STO
–––
–––
–––
SEL
0s
0s
0s
0s
Lap display –––
Note:
In the case described in these two examples,
“switchable” use of the C1 stick flight phase
timers for the separate measurement of the
motor run and possibly gliding times must be used.
Otherwise, each operation of the C1 stick would have
only one common time table stop described below
as result. The assignment of the selected transmitter
switch is as described below in »Timers (general.)”.
Otherwise, go to the menu ...
»Timers (general)« (page 164)
… and select the line "Top" with the selection keys.
This is the standard line assigned to the stopwatch.
In this line, move the marker frame over the "Timer"
column to the right, to the column above the switch
symbol, using the appropriate selection key of the left
or right touch pad. Now tap twice on the centre SET
key of the right touch pad: The first tap will activate
the “Switch assignment”, the second tap will call up
the list of "expanded switches":
Model time
Batt. time
Timer
–––12:34h
1:23h
0:00
0:00
0s
0s
–––
–––
Alarm
Timer
Top :Stoppuhr
Centr.Mitte :Flugzeit
Movwünschten Schalter
to die EIN Position
(erw. Schalter: SET)
Control/Logic/fix switch
C2 C4 C5 C6
C7 C8 FX FXi L1 L2
C3C1
Now select the previously programmed control switch,
C1 in the example, and assign it to the timer with a
brief tap on the centre SET key of the right touch pad:
Examples 4 and 5 of the preceding pages
If model programming is to be continued for Ex-
ample 4 (page 300) or Example 5 (page 303) as
described on previous pages or, completely inde-
pendent of this example programming, the C1 stick
(throttle/brake stick) is to be used for power regula-
tion, then a control switch can be used to automati-
cally start and stop the stopwatch. For this purpose,
first switch to the menu …
»Control switch« (page 146)
… and select the line of a control switch which has
not been assigned yet with the selection keys. After
activation of the control assignment with a brief tap
on the centre SET key of the right touch pad, the fol-
lowing window will appear:
SEL
0%
0%
0%
C1
C2
C3
–––
C4
CONTROL SWITCH
Geb. 1
0%
STO
–––
–––
–––
SEL
C1
C2
C3
C4
frei
free
free
frei Move desired
control adj.
Now simply move the C1 stick (throttle/brake stick)
from the motor "OFF" position in the motor "ON"
direction.
Thereafter, change to the column above STO by us-
ing the appropriate selection key, move the C1 stick
close to its motor "OFF" position then set the switch-
point at the selected position with a brief tap on the
centre SET key of the right touch pad. The switch's
state will be displayed at the right of the control num-
ber, e. g.:
Timer conrmation with control or switch
304


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC 32 HOTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC 32 HOTT in the language / languages: English as an attachment in your email.

The manual is 46,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC 32 HOTT

Graupner MC 32 HOTT User Manual - German - 320 pages

Graupner MC 32 HOTT User Manual - Dutch - 328 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info