467111
257
Zoom out
Zoom in
Previous page
1/345
Next page
257
Program description - Telemetry
SETTING & DATAVIEW sensor(s)
If one or more sensors are connected to a receiver,
and this receiver is a telemetry link, you can view the
displays of any sensor subsequent to the above-de-
scribed display “RX SERVO TEST” and if necessary
change its settings.
Type transmitter mc-32 HoTT with firm-
ware version V1.050 or higher, recognize
automatically a sensor connected to the
receiver:
GENERAL MODULE
RECEIVER
VARIO MODULE
AIR ESC
GPS
ELECTR. AIR MODULE
There is no automatic detection of connected
sensors, these are shown here in the »Te-
lemetry« menu’s »SENSOR SELECT« sub-menu
(described below) then its settings can be manually
select or activate in addition to the previously de-
scribed receiver screens:
SENSOR SELECT
RECEIVER
GENERAL MODULE
VARIO MODULE
ELECTRIC AIR.MOD
GPS
AIR ESC
However, to actually gain access to this data, the
selected sensor/s must be connected to the receiver
system and this receiver system must have an active
telemetry connection.
If, as described in the next section, there is at least
one sensor activated which has the support of current
firmware, then it is possible to directly switch between
individual modules. However, if sensors with older
firmware are in use, it may be necessary to select
“etc. instead of the direct sensor selection.
In either case, tap the or selection key of the left
touch pad…
RECEIVER
etc.
GENERAL
… then use the same keys to select up or down for
the desired module, for example:
GENERAL
RECEIVER
AIR ESC
When you again press the central SET button of the
right-hand touch pad then you confirm your choice.
If the selected module, in this case a Vario module, is
active then on the last receiver screen ("RX SERVO
TEST"), at the top right there will also be an addi-
tional " " symbol pointing to the right. This symbol is
located just to the right of the left-pointing " " symbol
and is the visible indicator that additional display
screens can be accessed.
TELEMETRY
SETTING & DATAVIEW
SENSOR SELECT
RF STATUS VIEW
VOICE TRIGGER
TELEMETRI RCV BIND. 1
VOLT.E
RX SERVO TEST V3.98
ALL–MIN : 1000µsec
ALL–MAX : 2000µsec
ALARM VOLT : 3.8V
ALARM TEMP–:–10°C
ALARM TEMP+: 70°C
TEST : START
CH OUT TYPE:ONCE
Now use one of the selection keys on the left or
right touch pad to switch to the selected sensor's dis-
plays and check or change its settings as described
in the manual delivered with the sensor.
257


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner MC 32 HOTT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC 32 HOTT in the language / languages: English as an attachment in your email.

The manual is 46,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC 32 HOTT

Graupner MC 32 HOTT User Manual - German - 320 pages

Graupner MC 32 HOTT User Manual - Dutch - 328 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info