Manual Graupner MC 32 HOTT (page 251 of 345) (English)

467111

251

Zoom out

Zoom in

1/345

251

Program description - Telemetry

In this case, the servo connection 04 would, in turn,

react according to the fail-safe settings of CH 01.

The reaction or delay time set in the "DELAY" line, on

the other hand, always applies uniformly for all chan-

nels set to "FAI(L) SAFE".

RX FREE MIXER

TELEMETRY

SETTING & DATAVIEW

SENSOR SELECT

RF STATUS VIEW

VOICE TRIGGER

TELEMETRI RCV BIND. 1

RX FREE MIXER V3.98

MASTER CH: 00

SLAVE CH : 00

S–TRAVEL–: 100

S–TRAVEL+: 100

MIXER : 1

RX WING MIXER

TAIL TYPE: NORMAL

Value Explanation Possible settings

Xx.xx Receiver’s

ﬁrmware version

None

MIXER Mixer selection 1 … 5

MASTER

Signal source or

source channel

0, 1 … depending

on receiver

SLAVE CH Target channel 0, 1 … depending

on receiver

S-TRAVEL– Admix negative 0 … 100 %

S-TRAVEL+ Admix positive 0 … 100 %

RX WING

MIXER

TAIL TYPE

tail type NORMAL,

V-TAIL, ELEVON

(vertical/horizontal

mixer for delta and

ﬂying wing)

MIXER

Up to ﬁve mixers can be programmed simultaneously.

Use "MIXER" to switch between mixers 1 … 5.

The following settings in this display always for just

the mixer selected in the "MIXER" line.

Important notice:

If you have already programmed

mixer functions in the »Wing mixer«

or »Free mixer« menus, make

absolutely sure that these mixers do not

overlap with those in the menu "RX FREE

MIXER"!

MASTER CH ("from")

According to the same principles described in the

section "Free mixer" on page 208, the signal applied

at the MASTER CH (signal source or source channel)

is mixed to a variable extent to the SLAVE CH (target

channel).

Select "00" if no mixer should be set.

SLAVE CH ("to")

The signal of the MASTER CH (source channel) is

mixed proportionally to the SLAVE CH (target chan-

nel). The mix ratio will be determined by the percent-

ages entered in the lines "TRAVEL–" and "TRAVEL+".

Select “00” if no mixer should be set.

TRAVEL–/+ (proportion of the admix in %)

With the settings of these two lines the percentage

of the admix is speciﬁed in relation to the MASTER

signal separately for each direction.

RX WING MIXER TAIL TYPE (tail unit type)

The following model types are also available in the

“Tail" line of the »Model type« menu, on page 104

and should, preferentially, be preset there. In this

case, always leave the TAIL TYPE set to NORMAL.

However, if you would prefer to use the mixer inte-

grated in the receiver, you can select the already

pre-adjusted mixer functions for the corresponding

model type:

• NORMAL

This setting corresponds to the classic aircraft

type with rear tail unit and separate rudder and

elevator. No mixer function is necessary for this

model type.

• V-TAIL (V-tail unit)

With this model type the elevator and rudder

control functions are connected, so that each

of the two tail unit ﬂaps – each controlled with a

separate servo – assume both the elevator and

rudder function.

The servos are normally connected to the receiver

as follows:

OUTPUT CH 3: Left V-tail servo

OUTPUT CH 4: Right V-tail servo

If the servo's direction of rotation is incorrect,

please observe the notices on page 66.

• ELEVON (delta/ying wing models)

The servos connect at the outputs 2 and 3 assume

the aileron and elevator function. The servos are

normally connected to the receiver as follows:

OUTPUT CH 2: Left horizontal/vertical

OUTPUT CH 3: Right horizontal/vertical

If the servo's direction of rotation is incorrect,

please observe the notices on page 66.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Graupner MC 32 HOTT in the language / languages: English as an attachment in your email.

The manual is 46,26 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Graupner MC 32 HOTT

Graupner MC 32 HOTT User Manual - German - 320 pages

Graupner MC 32 HOTT User Manual - Dutch - 328 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Graupner MC 32 HOTT Manual

Product: