637250
15
Zoom out
Zoom in
Previous page
1/20
Next page
15- 20
GR-10C_jh_V1
Roll and Nick setting
For Attitude and Rate mode:
ROLL/NICK P
Set this parameter in steps of 5 higher and higher, until a medi-
um-speed overshoot occurs. Then go some steps back in order
to prevent the soar up climb in case of full throttle.
ROLL/NICK D
Now adjust well to the D component in steps of 5, until the Cop-
ter engages exactly on nick and roll. A too high value leads to
very rapid oscillations.
DAMPING
The damping factor should be set as low as possible, but as
high as necessary, so that the PID control can operate optimally
and the setting can be increased at best. If you do not get vibra-
tions away with the PID settings , then change the damping of
a step and test whether the setting works better or worse. Rec-
ommended settings:
For Racecopter with fast controllers and 5-6 inch propellers: 1
- 2
For copters with fast controllers and 8 inch propellers: 2
Copter with bigger propellers: 2 or higher.
ROLL FACTOR %
Set the Roll setting as percent value of the overall gain. For sym-
metric Copters the value can be 100. If, because of its gravity
centre, the Copter is more agile on the Roll axis than on the Nick
axis, then you can change here the roll factor. In the Graupner
ALPHA RACE 250 Q this value is set about 65%.
POWER2SENS.:
Very strong drives can lead to oscillating at full throttle. This
parameter allows you to set a kind of gyro suppression. Higher
values result in an increased gyro suppression towards full throt-
tle.
Only fo attitude mode
ROLL/NICK I
Set the I component of the Attitude mode. At too low values of
Copter swings slowly. If it stops after a roll or pitch command
and “oscillates”, the value must be reduced.
AGILITY
Agility determines at what speed (yaw rate) a new position is
occupied.
Only for rate mode
R/N rate I
Sets the I component of the rotation in rate mode. At too low
values of Copter swings slowly. If it stops after a roll or pitch
command and “oscillates”, the value must be reduced.
RATE: Sets the max. potential rate of rotation in Rate mode.
Multicopter RO/NI< >
>ROLL/NICK P 40
ROLL/NICK D 30
DAMPING 2
ROLL FACTOR % 100
POWER2SENS. 80
--ATTITUDE MODE--
ROLL/NICK I 40
AGILITY 3
Multicopter RO/NI< >
--RATE MODE--
R/N RATE I 20
RATE 6
Step 4
Optional setting for Roll and Nick
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graupner GR-10C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graupner GR-10C in the language / languages: English as an attachment in your email.

The manual is 1,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info