738282

Grasslin Telltask 1C1 Manual

10
Zoom out
Zoom in
Previous page
1/40
Next page
telltask 1C1
10
10
Hinweis: Die gesendeten Befehle müssen in Großbuchstaben geschrieben sein und dürfen keine Leerschritte auf-
weisen.
Fehlerbehebung
Bei Störungen sendet die LED zur Fehleranzeige rote Blinksignale.
Zum Identifizieren des unten aufgeführten Fehlercodes die Blinksignale zählen:
Blinksignale
Beschreibung
1
GSM-Signal nicht erfasst wird
2
Die SIM-Karte ist durch eine PIN-Zahl geschützt.
3
Keine SIM-Karte.
4
Die SIM-Karte funktioniert nicht
5
Systemfehler: Das Gerät neu starten
6
Die SIM-Karte ist durch eine PUK-Zahl geschützt.
Kenndaten
Kommunikation
• UMTS / HSPA / GSM 900MHz ,1800MHz, 2100MHz
Versorgung
• Anschlussspannung: 5.3 -12V DC
• Stromstärke: Imax = 800mA
• Die Versorgungsspannung darf die maximale Leistung von 24VA nicht überschreiten.
• Versorgung gegen Polaritätsvertausch abgesichert
Relaisausgang
• 1 Relay SPDT
o 0,5A, 250V AC (Ohmsche Last);
o 1A, 30V DC.
Eingänge
• 1 digital-Eingang (VCC), (potentialfrei)
Haupteigenschaften
• Gehäuse für Schiene EN-50022: UL94V-0;
• Schutzart: IP20.
• Standardbetriebstemperatur: von -5°C bis +45°C;
• maximaler Querschnitt der Leiter, die in die Klemmen eingesetzt werden können: 2,5mm2;
• USB-Programmierport
Geprüft nach
• 2014/53/EU (RED)
• 2014/30/UE (EMV)
• 2014/35/UE (LVD)
• FCC/CE/TELEC/KCC/SRRC/IC/NCC
Verbrauch
(Standardwerte)
Standby 40mA
Senden/Empfangen SMS 200mA
Softwareanforderungen
In der nachfolgenden Tabelle sind die von der Software telltask 1C1 unterstützten Betriebssysteme aufgeführt.
Betriebssystem
Notes
Windows 7
dieser Software wird auf IA-64-basierten Systemen (Itanium) nicht unterstützt.
Um die bestmögliche Kompatibilität und höchste Sicherheit zu gewährleisten, wird für alle Plattfor-
men empfohlen, ein Upgrade auf das neueste Windows Service Pack durchzuführen und wichtige
Updates zu installieren, die auf der Windows Update-Website verfügbar sind.
Windows 8
Windows 10
11
Safety Information
• Do not install the telltask 1C1 device close to pacemakers, auditory prostheses or medical devices in general
as the telltask 1C1 device may interfere with the operation of these devices.
• The telltask 1C1 device operates by means of a radio signal, no mobile telephone operator is capable of ensuring
a connection at all times. For this reason, the telltask 1C1 device cannot be used in life support systems.
Notes
• All information contained in this manual is subject to change without prior notice.
• No part of this manual may be reproduced, in any form or by any means, electronic or physical, or otherwise,
including photocopying or storage, for needs other than the personal use of the user, without the prior written
permission by .
• The use, copying, modification, disassembly or transmission of the software is forbidden.
• For any other trademark or product cited reference is made to relative owner.
Installation
In order to ensure the operator's safety and the correct operation of the telltask 1C1, the device should be installed
exclusively by qualified staff. The rules listed below have to be strictly observed.
Environmental conditions
The telltask 1C1 device (the instrument and all cables connected to it) should be installed in places either free or
far from:
• Dust, humidity, intense heat;
• Direct exposure to sunlight;
• Objects radiating heat;
• Objects generating a strong electromagnetic field;
• Liquids or corrosive chemical substances.
Degree of Protection
During the installation of the telltask 1C1 device, the following degree of protection is to be ensured:
• IP54: protection to be guaranteed when using the device outdoors.
Power supply
Observe the following rules:
• Do not use cables longer than 2m;
• The external power supply unit (e.g. plug-in power supply), must comply with the EN 60950 Directive (electrical
safety);
• The device must be powered by a power source limited to 24VA.
Signaling Inputs
Observe the following rules:
• do not use cables longer than 2m;
• do not install the cables in proximity of possible electromagnetic fields, in which case, use shielded cables.
Relay Output
Observe the following rules:
• before connecting the load, check the data rating. (see "rating");
• use insulated cables suitable for the load with double sheath (double insulation), with 6 mm outer sheath diam-
eter;
• ensure that dangerous voltage cables go along the path indicated only remaining within the A.T. area;
• do not put a cable longer than expected (2m), and especially outside the indicated areas;
• you should never bring dangerous voltage cables close the low voltage.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Grasslin Telltask 1C1 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Grasslin Telltask 1C1 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 2,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info