354442
30
Zoom out
Zoom in
Previous page
1/42
Next page
GB
30
It is also important that the cabinet stands
absolutely level. The setting screws under
the cabinet can be adjusted to make sure
that it does stand level.
Illustration shows how easy it is to
change the door from righthand to left-
hand-hinged - or vice versa.
Proceed as follows.
Is your refrigerator fitted with a tabletop
remove the tabletop thus:
Loosen the four screws with a screw-
driver. The tabletop can now be drawn out
of the frame . The tabletop frame can
be loosened by removing the two front
screws with a key .
Lay the cabinet on its back with door
uppermost.
Take off the door handle using a
screwdriver.
Remove the two supporting rails under-
neath the cabinet (not applicable to cabi-
nets with a base).
On TU-cabinets remove the two front legs
(the legs nearest the door) thus:
Screw the nylon leg out manually. The
screw in the bush can be removed with
a screwdriver. Both bush and inner washer
can then be removed.
To remove the door, remove the cover-
plugs with a knife or something similar
and then the screws using a key as
shown on the drawing.
Move the hinges and dummy hinges
diagonally (upper righthand hinge to
lower lefthand corner and lower righthand
hinge to upper lefthand corner).
11
10
9
8
7
5
4
6
3
2
1
2
When the door is mounted, a 9 mm filler
(wood or something similar) should be
placed between the front of the cabinet
and the edge of the door to create suffici-
ent space for the sealing strip.
Remember to place the correct number of
washers beneath the bottom hinge to en-
sure that the door has the correct height.
Replace the supporting rails and install the
cabinet.
Once the cabinet has been placed in its
correct position, the hinges may need
readjustment. The elongated holes in the
hinges make this readjustment possible so
that the sealing strips provide optimum
sealing all the way round.
If during transport the refrigerator has
been laid down, or if it has been stored in
cold surroundings (colder than +5°C) it
must be allowed to stabilise for at least 1
hour before switching on.
Start the refrigerator by plugging into a
wall socket.
The cabinet is intented for connection to
alternating current. The connection values
for voltage (V) and frequency (Hz) are
given on the nameplate placed in the cabi-
net.
Power must be connected via a wall
socket with a switch. The wall socket sho-
uld be easily accessible.
All earthing requirements stipulated by
local electricity authorities must be obser-
ved. The cabinet plug and wall socket
should then give correct earthing. If in
doubt, contact your supplier or authorized
electrician.
3
Starting up
Electrical connection
You can change the
door from righthand to
lefthand - hinged or
vice versa yourself
30


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gram ks 15201g at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gram ks 15201g in the language / languages: English, German, Dutch, Danish, French, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 0,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info