Manual Graco SlimFit LX (page 10 of 47) (English, German, Dutch, French, Italian, Portuguese, Spanish)

768343

Zoom out

Zoom in

1/47

17 18

 Rear-facing with an active front air bag.

 Booster mode with vehicle lap-only seat belt-

Review your vehicle owner’s manual for vehicle seat belt use.

 Vehicle seat’s headrest SHOULD NOT create a gap between

vehicle seat and booster seat-

The front of booster seat base MUST NOT hang over front of

vehicle seat.

If child will not keep the vehicle seat belt properly positioned,

DO NOT use this booster seat. Use a diﬀerent child restraint

system.

 Headrest Pad-

If needed, headrest pad may be removed for cleaning.

A To remove, unsnap the pad to pull the harness straps out.

B Pull the plastic tab out of the slots just below the red

adjustment handle.

C Remove the elastic straps from the hooks on both sides of

the headrest.

D Pull pad off of headrest. Machine wash cover in cold water on

delicate cycle and drip-dry. DO NOT USE BLEACH. Reverse the

steps to reattach the cover on the headrest.

 Lower Seat Pad-

If needed, lower seat pad may be removed for cleaning.

A To remove, unsnap lower seat pad from side pad.

B Undo the plastic hooks on both armrest.

C Unhook the elastic strap from both armrests. Pull the pad off.

Machine wash cover in cold water on delicate cycle and drip-

dry. DO NOT USE BLEACH.

Reverse the steps to reattach the bottom seat pad. In the

front, place the shell in the pocket on the pad.

 Side Pad-

If needed, side pad may be removed for cleaning.

A To remove, lower headrest and unhook the pad from back.

B Pull the plastic tabs out from the back and sides of the seat.

C Remove the elastic straps from the hooks in the forward-

facing belt path. Pull the pad off.

Machine wash cover in cold water on delicate cycle and drip-

dry. DO NOT USE BLEACH.

Reverse the steps to reattach the bottom seat pad. Place the

corner of the sidewing in the pocket at the bottom of the

side pad.

 Cleaning Harness Covers-

Wipe clean with damp cloth.

 Cleaning Crotch Buckle-

WARNING! Inspect and clean buckle from time to time to

remove any objects or debris that could prevent latching.

A Recline the child restraint system and locate the metal

retainer.

B Rotate the metal retainer up through the shell and pad. From

the front, pull the crotch buckle out.

C To clean buckle, place in a cup of warm water and gently

agitate the buckle. Press the red button several times while in

the water.

DO NOT SUBMERGE THE BUCKLE STRAP. DO NOT USE SOAPS,

HOUSEHOLD DETERGENTS or LUBRICANTS.

D Shake out excess water and allow to air dry. Repeat steps as

needed until it fastens with a click. Re-insert the buckle into

the same slot it was removed. Pull up on crotch buckle to

make sure it is secured.

Make sure that both ISOcatch connectors are securely

attached to their ISOFIX anchor points. The colors of

the indicators on both ISOcatch connectors should be

completely green.

Place forward-facing on a vehicle seat that has a lap/

shoulder seat belt. The base should sit as ﬂat as possible on

the vehicle seat.

Securing Child In Booster

 Place Child In Seat-

Have your child sit in the booster seat with their back ﬂat

against the back of the booster seat.

 Thread vehicle’s shoulder belt through booster shoulder belt

guide in the headrest.

 Buckle the Vehicle Lap/Shoulder Seat Belt-

Be sure the lap portion of the vehicle seat belt goes behind

the armrests marked with a dark red label.

Both the lap and shoulder belt must lay in the booster belt

path on the buckle side of the seat marked with a dark red

label.

 Be sure the lap portion of the vehicle seat belt is low across

your child’s hips and is adjusted snugly.

 Vehicle seat’s shoulder belt should be centered between the

child’s neck and edge of shoulder.

Raise or lower the headrest to change the shoulder belt

location on the child.

Accessories (on select models)

 Body Support-

Body support must be used if shoulders are below the lowest

harness setting.

Never allow body support to bunch or fold behind child. To

remove, unbuckle the buckle and pull out the body support.

 For infants weighing 0-5 kg, use the body support wedge.

Remove the wedge for infants over 5 kg.

 Headrest Pillow-

To remove, pull the pillow out.

 Cup Holder-

Cup holder can be on either side.

To attach, pull back the seat pad to expose the attachment

guide A . Slide the cup holder down the guide until it locks

into place B .

To remove, place both hands under the cup holder and push

up on the cup holder C .

Choosing Vehicle Seat Location

Review your vehicle owner’s manual for seating locations.

The best seating location for this child restraint system is one that:

Is recommended by your vehicle owner’s manual

Results in a secure installation of this child restraint system.

Unsafe Vehicle Seat Locations

Never install this child restraint system in any of the following

vehicle seating locations:

 Rear-facing or side-facing vehicle seats.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Graco SlimFit LX in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 1,93 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Graco SlimFit LX Manual

Product: