768361
6
Zoom out
Zoom in
Previous page
1/42
Next page
910
Rotate the lower back support
up while holding the booster
seat until it clicks into an upright
position.
Align the side impact shield with
the slot of lower back support
plastics mounts, and then insert
to lock.
! Please choose whether to install
the side impact shield according
to the size of the car.
Height Adjustment
– for Head Support
See images
Squeeze the head support
adjustment lever while pulling
up or down on the head support
until it snaps into one of the 10
positions.
Concerns on
Installation
See images - 
Installation with
3-point-belt
See images  - 
If vehicle is equipped with ISOFIX, the
vehicle lower anchor points may be
visible at the vehicle seat crease. See
your vehicle owner’s manual for exact
locations, anchor identication, and
requirements for use.
 Place the booster in forward-
facing position on a forward
facing vehicle seat with anchors,
hook latch connectors to vehicle
anchors.
! NEVER put two latch connectors
on one vehicle ISOFIX anchor
unless specically allowed by
the vehicle manufacturer.
 Secure the booster rmly by
pushing it downward with
knee or hand while pulling the
adjustment belt.
 For ease of unhooking, extend
the adjustment belt to its
maximum length while pressing
the adjustment button.
! The latch connectors can be
detached for use from the
compartment on the bottom
where it is stored.
! Pull the vehicle safety belt and
pass through the belt path, 
and then buckle it up.  -3
! Could also be installed by using
3-point belt only. (See images
 -  )
! Position shoulder belt through
the shoulder belt guide shown
in  -1
! DO NOT position vehicle belt
over top of the armrests. It must
pass underneath the armrests.
 -2
! The booster can not be used if
the vehicle safety belt buckle
(female buckle end) is too long
to anchor the booster securely.
 -4
! After your child is placed in this
booster, the safety belt must
be used correctly, and ensure
that any lap strap is worn low
down, so that the pelvis is rmly
engaged. 
! To ensure the correct head
support height is obtained, the
bottom of the headrest MUST
be even with the top of child’s
shoulders as shown in 
and the shoulder belt must be
positioned in the green zone as
shown in 
! Place a booster rmly against
the back of a forward-facing
vehicle seat equipped with a
lap/shoulder belt. ! Make sure,
that the shoulder belt portion
of the vehicle belt goes straight
through the shoulder belt guide
as shown in 
! Tighten the vehicle belt by
pulling the shoulder strap until
all belt slack is removed.
! If the belt lays across child neck,
head or face, readjust head
support height.
! Any straps holding the booster
to the vehicle should be tight
and the straps should not be
twisted.
Use Cupholders
See images 
Detach Soft Goods
See images 
Open 2 pairs of buttons and 6 pairs of
elastics on the back of soft goods to
remove it. 
To ret the seat pad simply reverse
the steps above.
Care and
Maintenance
Please wash the seat cover and inner
padding with cold water under 30°C.
Do not iron the soft goods.
Do not bleach or dry clean the soft
goods.
Do not use undiluted detergents,
gasoline or other organic solvent to
wash the child restraint. It may cause
damage to the child restraint.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Graco EverSure at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Graco EverSure in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 2,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info