Manual Graco Avolve (page 9 of 66) (English, German, Dutch, French, Italian, Polish, Portuguese, Spanish)

768339

Zoom out

Zoom in

1/66

15 16

Booster Install

Store the Harness

 Loosen the harness straps as much as possible.

 Raise the headrest to the highest position.

 Unbuckle the buckle.

 Remove the crotch belt cover and the lower seat pad to

expose the harness storage door. ( A , B , C )

 Remove Buckle-

A Recline the child restraint system and locate the metal

retainer.

B Rotate the metal retainer up through the shell and pad. from

the front, pull the crotch buckle out.

 Store Buckle and Crotch Belt Cover-

Open the harness storage door and place harness, buckle,

buckle tongues and crotch belt cover inside storage

compartment. Close the door.

 Store Harness Covers-

Place the harness covers in the shell back openings as shown.

 Replace Seat Pad-

Move the headrest back to its proper position for your child.

 Recline the Child restraint system-

Place the booster seat in recline position 4.

 Place the Booster Seat Forward-Facing in the Vehicle Seat-

Installation with ISOcatch attachment is as  - 

Make sure that both ISOcatch connectors are securely

attached to their ISOFIX anchor points. The colors of

the indicators on both ISOcatch connectors should be

completely green.

Place forward-facing on a vehicle seat that has a lap/

shoulder seat belt. The base should sit as at as possible on

the vehicle seat.

Securing Child In Booster

 Place Child In Seat-

Have your child sit in the booster seat with their back at

against the back of the booster seat.

 Thread vehicle’s shoulder belt through booster shoulder belt

guide in the headrest.

 Buckle the Vehicle Lap/Shoulder Seat Belt-

Be sure the lap portion of the vehicle seat belt goes behind

the armrests marked with a dark red label.

Both the lap and shoulder belt must lay in the booster belt

path on the buckle side of the seat marked with a dark red

label.

Contact Graco if in doubt about this point. The seat belt

should lay as flat as possible and not be twisted.

 Be sure the lap portion of the vehicle seat belt is low across

your child’s hips and is adjusted snugly.

 Vehicle seat’s shoulder belt should be centered between the

child’s neck and edge of shoulder.

Raise or lower the headrest to change the shoulder belt

location on the child.

Accessories (on select models)

 Body Support-

Body support must be used if shoulders are below the lowest

harness setting.

Never allow body support to bunch or fold behind child. To

remove, unbuckle the buckle and pull out the body support.

 Cup Holder-

Cup holder can be on either side.

To attach, pull back the seat pad to expose the attachment

guide A . Slide the cup holder down the guide until it locks

into place B .

To remove, place both hands under the cup holder and push

up on the cup holder C .

Choosing Vehicle Seat Location

Review your vehicle owner’s manual for seating locations.

The best seating location for this child restraint system is one that:

Is recommended by your vehicle owner’s manual

Results in a secure installation of this child restraint system.

Unsafe Vehicle Seat Locations

Never install this child restraint system in any of the following

vehicle seating locations:

 Rear-facing or side-facing vehicle seats.

 Booster mode with vehicle lap-only seat belt-

Review your vehicle owner’s manual for vehicle seat belt use.

 Vehicle seat’s headrest SHOULD NOT create a gap between

vehicle seat and booster seat-

The front of booster seat base MUST NOT hang over front of

vehicle seat.

If child will not keep the vehicle seat belt properly positioned,

DO NOT use this booster seat. Use a dierent child restraint

system.

 Cleaning Headrest Pad-

If needed, headrest pad may be removed for cleaning.

A To remove, unsnap the pad to pull the harness straps out.

B Pull the plastic tab out of the slots just below the red

adjustment handle.

C Remove the elastic straps from the hooks on both sides of

the headrest.

D Pull pad off of headrest. Machine wash cover in cold water on

delicate cycle and drip-dry. DO NOT USE BLEACH. Reverse the

steps to reattach the cover on the headrest.

 Lower Seat Pad-

If needed, lower seat pad may be removed for cleaning.

A To remove, unsnap lower seat pad from side pad.

B Undo the plastic hooks on both armrest.

C Unhook the elastic strap from both armrests. Pull the pad off.

Machine wash cover in cold water on delicate cycle and drip-

dry. DO NOT USE BLEACH.

Reverse the steps to reattach the bottom seat pad. In the

front, place the shell in the pocket on the pad.

 Side Pad-

If needed, side pad may be removed for cleaning.

A To remove, lower headrest and unhook the pad from back.

B Pull the plastic tabs out from the back and sides of the seat.

C Remove the elastic straps from the hooks in the forward-

facing belt path. Pull the pad off.

Machine wash cover in cold water on delicate cycle and drip-

dry. DO NOT USE BLEACH.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Graco Avolve in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish as an attachment in your email.

The manual is 1,79 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Graco Avolve Manual

Product: