Manual Gossen Metrawatt Profitest Intro (page 56 of 62) (English)

776259

Zoom out

Zoom in

1/62

56 GMC-I Messtechnik GmbH

19.2 At which values should/must an RCD actually be tripped?

Requirements for Residual Current Devices (RCDs)

General Requirements

• Tripping must occur no later than upon occurrence of rated re-

sidual current (nominal differential current IΔN).

and

• Maximum time to trip may not be exceeded.

Additional requirements due to influences on the tripping current range

and the point in time of tripping which have to be taken into consider-

ation:

• Residual current type or waveform:

This results in a reliable tripping current range.

• Mains type and line voltage:

This results in maximum tripping time.

• RCD variant (standard or selective):

This results in maximum tripping time.

Definitions of Requirements in the Standards

VDE 0100-600, which is included in all German standards collec-

tions for electricians, applies to measurements in electrical sys-

tems. It plainly states: “The effectiveness of the protective mea-

sure is substantiated when shut-down occurs no later than upon

occurrence of rated differential current IΔN.”

As a requirement for the measuring instrument manufacturer,

DIN EN 61557-6 (VDE 0413-6) unmistakable specifies:

“The measuring instrument must be capable of substantiating the

fact that the residual current which trips the residual current

device (RCD) is less than or equal to rated residual current.”

Comment

For all electricians, this means that during scheduled testing of

protective measures after system modifications or additions to the

system, as well as after repairs or during the E-check conducted

after measurement of touch voltage, the trip test must be con-

ducted no later than upon reaching a value of, depending upon

the RCD, 10 mA, 30 mA, 100 mA, 300 mA or 500 mA

How does the electrician react in the event that these values are

exceeded? The RCD is replaced!

If it was relatively new, a complaint is submitted to the manufac-

turer. And in his laboratory he determines: The RCD complies with

the manufacturer’s standard and is OK.

A look at the VDE 0664-10/-20/-100/-200 manufacturer’s stan-

dard shows us why:

Because the current waveform plays a significant role, the current

waveform used by the test instrument is also important.

Set residual current type or waveform at the test instrument:

It’s important to be able to select and take advantage of the cor-

responding settings at one’s own test instrument.

The situation is similar for breaking times. The new VDE 0100-410

should also be included in the standards collection.

Depending upon mains type and line voltage, it specifies breaking

times ranging from 0.1 to 5 seconds.

RCDs usually interrupt more quickly, but in some cases they can

take a bit longer. Once again, the ball is in the manufacturer’s

court.

The following table is also included in VDE 0664:

Two limit values are highly conspicuous:

Standard Max. 0.3 sec.

Selective Max. 0.5 sec.

All of the limit values are already included in good test instru-

ments, or it’s possible to enter them directly and they’re displayed

as well!

Select or set limit values at the test instrument:

Tests for electrical systems include “visual inspection”, “testing”

and “measurement”, and thus may only be conducted by experts

with appropriate work experience.

In the final analysis, the values from VDE 0664 are technically

binding.

Type of Residual Current Waveform of the

Residual Current

Permissible

Tripping Current

Range

Sinusoidal alternating current 0.5 ... 1 IΔN

Pulsating direct current

(positive or negative half-waves) 0.35 ... 1.4 IΔN

Phase angle controlled

half-wave currents

Phase angle of 90° el

Phase angle of 135° el

0.25 ... 1.4 IΔN

0.11 ... 1.4 IΔN

Pulsating direct current superimposed

with 6 mA smooth, direct residual current Max. 1.4 IΔN + 6 mA

Smooth direct current 0.5 ... 2 IΔN

System

50 V < U

≤

120 V

120 V < U

≤

230 V 230 V < U

≤

400 V

U0 > 400 V

AC DC AC DC AC DC AC DC

TN 0.8 sec. 0.4 sec. 5 sec. 0.2 sec. 0.4 sec. 0.1 sec. 0.1 sec.

TT 0.3 sec. 0.2 sec. 0.4 sec. 0.07 sec. 0.2 sec. 0.04 sec. 0.1 sec.

Variant

Residual

Current

Type

Braking Time at

Alternating re-

sidual current 1 x IΔN2 x IΔN5 x IΔN500 A

Pulsating

direct residual

current

1.4 x IΔN2 x 1.4 x IΔN5 x 1.4 x IΔN500 A

Smooth,

direct residual

current

2 x IΔN2 x 2 x IΔN5 x 2 x IΔN500 A

Standard

(undelayed)

or briefly

delayed

300 ms Max. 0.15 sec. Max. 0.04 sec. Max. 0.04 sec.

Selective 0.13 ... 0.5 s 0.06 ... 0.2 s 0.05 ... 0.15 s 0.04 ... 0.15 s

Negative half-wave

Positive half-wave

Waveform:

Negative direct current

Positive direct current

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gossen Metrawatt Profitest Intro in the language / languages: English as an attachment in your email.

The manual is 1.69 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gossen Metrawatt Profitest Intro Manual

Product: