590777

Gossen Metrawatt PROFITEST MXTRA Manual

6
Zoom out
Zoom in
Previous page
1/96
Next page
6 GMC-I Messtechnik GmbH
2.2 Overview of Features Included
with PROFITEST MASTER & SECULIFE IP Device Variants
1)
The so-called live measurement is only advisable if there is no bias current within
the system. Only suitable for motor circuit breaker with low nominal current
2
currently available languages: D, GB, I, F, E, P, NL, S, N, FIN, CZ, PL
3 Safety Features and Precautions
This instrument fulfills all requirements of applicable European and
national EC directives. We confirm this with the CE mark. The rel-
evant declaration of conformity can be obtained from GMC-I
Messtechnik GmbH.
The electronic measuring and test instrument is manufactured
and tested in accordance with safety regulations IEC 61010-1/
EN 61010-1/VDE 0411-1 and EN 61557.
Safety of the operator, as well as that of the instrument, is only
assured when it is used for its intended purpose.
Read the operating instructions thoroughly and carefully before using
your instrument. Follow all instructions contained therein. Make sure that
the operating instructions are available to all users of the instrument.
Tests may only be executed by a qualified electrician.
Grip and hold the test plug and test probes securely when they
have been inserted, for example, into a socket. Danger of injury
exists if tugging at the coil cord occurs, which may cause the test
plug or test probes to snap back.
The measuring and test instrument may not be placed into service:
• If the battery compartment lid has been removed
• If external damage is apparent
• If connector cable or measuring adapters are damaged
•If the instrument no longer functions flawlessly
• After a long period of storage under unfavorable conditions
(e.g. humidity, dust, temperature)
Exclusion of Liability
When testing systems with RCCBs, the latter may switch off. This may
occur even though the test does not normally provide for it. Leak-
age currents may be present which, in combination with the test
current of the test instrument, exceed the shutdown threshold
value of the RCCB. PCs which are operated in proximity to such
RCCB systems may switch off as a consequence. This may result
in inadvertent loss of data. Before conducting tests, precautions
should therefore be taken to ensure that all data and programs
are adequately saved, and the computer should be switched off if
necessary. The manufacturer of the test instrument assumes no
liability for any direct or indirect damage to equipment, comput-
ers, peripheral equipment or data bases when performing tests.
Opening of Equipment / Repair
The equipment may be opened only by authorized service per-
sonnel to ensure the safe and correct operation of the equipment
and to keep the warranty valid.
Even original spare parts may be installed only by authorized ser-
vice personnel.
In case the equipment was opened by unauthorized personnel,
no warranty regarding personal safety, measurement accuracy,
conformity with applicable safety measures or any consequential
damage is granted by the manufacturer.
Any warranty claims will be forfeited when the warranty seal has
been damaged or removed.
Meaning of Symbols on the Instrument
Warning concerning a point of danger
(Attention, observe documentation!)
Protection class II device
Charging socket for extra-low direct voltage (charger Z502R)
Attention!
Only rechargeable batteries may be inserted when the char-
ger is connected.
This device may not be disposed of with the trash. Fur-
ther information regarding the WEEE mark can be
accessed on the Internet at www.gossen-
metrawatt.com by entering the search term “WEEE”.
EC mark of conformity
PROFITEST ...
(Article Number)
MBASE+
(M520S)
M
PRO
(M520N)
M
TECH+
(M520R)
M
XTRA
(M520P)
SECULIFE IP
(M520U)
Testing of residual current devices (RCDs)
U
B
measurement without tripping RCD
3333
✓
Tripping time measurement
3333
✓
Measurement of tripping current I
F
3333
✓
Selective, SRCDs, PRCDs, type G/R
3333
✓
AC/DC sensitive RCDs, type B, B+ and EV ——
33
✓
Testing of IMDs ———
3
✓
Testing of RCMs ———
3
—
Testing for N-PE reversal
3333
✓
Measurement of loop impedance Z
L-P E
/ Z
L-N
Fuse table for systems without RCDs
3333
✓
Without tripping the RCD, fuse table ——
33
✓
With 15 mA test current
1
without tripping the
RCD
3333
✓
Earthing resistance R
E
(mains operation)
I-U measuring method (2/3-wire measuring
method via measuring adapter: 2-wire/2-wire +
probe)
3333
✓
Earthing resistance R
E
(battery operation)
3 or 4-wire measurement via PRO-RE adapter
—
3
—
3
—
Soil resistivity
E
(battery operation)
(4-wire measurement via PRO-RE adapter)
—
3
—
3
—
Selective earthing resistance R
E
(mains opera-
tion)
with 2-pole adapter, probe, earth electrode
and current clamp sensor (3-wire measuring
method)
3333
✓
Selective earthing resistance R
E
(battery operation)
with probe, earth electrode and current clamp
sensor (4-wire measuring method via PRO-RE
adapter and current clamp sensor)
—
3
—
3
—
Earth loop resistance R
ELOOP
(battery operation)
with 2 clamps (current clamp sensor direct
and current clamp transformer via PRO-RE/2
adapter)
—
3
—
3
—
Measurement of equipotential bonding R
LO
,
automatic polarity reversal
3333
✓
Insulation resistance R
ISO
,
variable or rising test voltage (ramp)
3333
✓
Voltage U
L-N
/ U
L-PE
/ U
N-PE
/ f
3333
✓
Special measurements
Leakage current (with clamp) I
L
, I
AMP
3333
✓
Phase sequence
3333
✓
Earth leakage resistance R
E(ISO)
3333
✓
Voltage drop (U)
3333
✓
Standing-surface insulation Z
ST
3333
✓
Meter start-up (kWh-Test)
3333
—
Leakage current with PRO-AB adapter (IL)
———
3
✓
Residual voltage test (Ures)
———
3
—
Intelligent ramp (ta + I)
———
3
—
Electric vehicles at charging stations
(IEC 61851)
——
33
—
Report generation of fault simulations on
PRCDs with PROFITEST PRCD adapter
———
✓
—
Features
Selectable user interface language
2
3333
✓
Memory (database for up to 50,000 objects)
3333
✓
Automatic test sequence function
3
2)
3 3 3
✓
RS 232 port for RFID/barcode scanner
3333
✓
USB port for data transmission
3333
✓
Interface for Bluetooth® ——
33
✓
ETC user software for PC
3333
✓
Measuring category: CAT III 600 V / CAT IV
300 V
3333
✓
DAkkS calibration
3333
✓
!
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gossen Metrawatt PROFITEST MXTRA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gossen Metrawatt PROFITEST MXTRA in the language / languages: English as an attachment in your email.

The manual is 2,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gossen Metrawatt PROFITEST MXTRA

Gossen Metrawatt PROFITEST MXTRA User Manual - Dutch - 92 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info