Manual Gossen Metrawatt PROFITEST MXTRA (page 5 of 96) (English)

590777

Zoom out

Zoom in

1/96

GMC-I Messtechnik GmbH 5

16.2 Transferring Distributor Structures ........................................... 66

16.3 Creating a Distributor Structure in the Test Instrument ........... 66

16.3.1 Creating Structures (example for electrical circuit) ......................... 67

16.3.2 Searching for Structural Elements ................................................ 68

16.4 Saving Data and Generating Reports ........................................ 69

16.4.1 Use of Barcode Scanners and RFID Readers ................................. 70

17 Operating and Display Elements ....................................71

18 LED Indications, Mains Connections and Potential Differences 73

19 Characteristic Values ......................................................82

20 Maintenance ...................................................................87

20.1 Firmware Revision and Calibration Information ....................... 87

20.2 Rechargeable Battery Operation, and Charging ....................... 87

20.2.1 Charging Procedure with Charger for Z502R ................................. 87

20.3 Fuses ........................................................................................ 87

20.4 Housing ..................................................................................... 87

21 Appendix .........................................................................88

21.1

Tables for the determination of maximum or minimum display values

under consideration of maximum measuring uncertainty: ...................88

21.2 At which values should/must an RCD actually be tripped?

Requirements for Residual Current Devices (RCDs) ................. 90

21.3 Testing Electrical Machines per DIN EN 60204 –

Applications, Limit Values ......................................................... 91

21.4 Periodic Testing per DGUV provision 3 (previously BGV A3) – Limit

Values for Electrical Systems and Operating Equipment .......... 92

21.5 List of Abbreviations and their Meanings ................................. 93

21.6 Keyword Index .......................................................................... 94

21.7 Bibliography .............................................................................. 95

21.7.1 Internet Addresses for Additional Information ............................... 95

22 Repair and Replacement Parts Service

Calibration Center and Rental Instrument Service .........96

23 Recalibration ..................................................................96

24 Product Support .............................................................96

1 Scope of delivery

1Test instrument

1 Earthing contact plug insert (country-specific)

1 2-pole measuring adapter and 1 cable for expansion into a

3-pole adapter (PRO-A3-II)

2 Alligator clips

1 Shoulder strap

1 Compact Master Battery Pack (Z502H)

1 Charger Z502R

1 DAkkS calibration certificate

1USB cable

1 Condensed operating instructions

1 Supplement Safety Information

– Detailed operating instructions for download from our website

at www.gossenmetrawatt.com

2 Applications

The PROFITEST MASTER and SECULIFE IP measuring and test instru-

ments allow for quick and efficient testing of protective measures

in accordance with DIN VDE 0100, part 600:2008

(Erection of low-

voltage installations; tests – initial tests), as well as

ÖVE-EN 1 (Aus-

tria), NIV/NIN SEV 1000 (Switzerland) and other country-specific

regulations.

The test instrument is equipped with a microprocessor and com-

plies with IEC 61557/EN 61557/VDE 0413 regulations:

Part 1: General requirements

Part 2: Insulation resistance

Part 3: Loop resistance

Part 4:

Resistance of earth connection and equipotential bonding

Part 5: Earth resistance

Part 6: Effectiveness of residual current devices (RCD) in TT, TN

and IT systems

Part 7: Phase sequence

Part 10:Electrical safety in low-voltage systems up to 1000 V AC

and 1500 V DC – Equipment for testing, measuring or

monitoring of protective measures

Part 11:Effectiveness of type A and type B residual current moni-

tors (RCMs) in TT, TN and IT systems

The test instrument is especially well suited for:

•System setup

• Initial start-up

• Periodic testing

• Troubleshooting in electrical systems

All of the values required for approval reports (e.g. for ZVEH) can

be measured with this instrument.

All acquired data can be archived, in addition to the measurement

and test reports which can be printed out at a PC. This is of spe-

cial significance where product liability is concerned.

The applications range of the test instruments covers all alternat-

ing and three-phase current systems with nominal voltages of

230 V / 400 V (300 V / 500 V) and nominal frequencies of 16

50 / 60 / 200 / 400 Hz.

The following can be measured and tested with the instruments:

• Voltage / frequency / phase sequence

• Loop impedance / line impedance

• Residual current devices (RCDs)

• Insulation monitoring devices (IMDs) (only

MXTRA

SECULIFE IP

)

• Residual current monitoring devices (RCMs) (only MXTRA)

• Earthing resistance / earth electrode potential

• Standing surface insulation resistance / insulation resistance

• Earth leakage resistance

• Low-value resistance (potential equalization)

• Leakage currents with current transformer clamp

• Residual voltage (only MXTRA)

• Voltage drop

• Leakage current with leakage current adapter

• Meter start-up (not

SECULIFE IP

)

• Cable length

Refer to section 21.3 regarding testing of electrical machines in

accordance with DIN EN 60204.

Refer to section 21.4 regarding periodic testing in accordance

with DGUV provision 3 (previously BGV A3).

2.1 Using Cable Sets and Test Probes

• 2 or 3-pole measuring adapter included

• 2-pole measuring adapter with 10 m cable as optional acces-

sory: PRO-RLO II (Z501P)

• KS24 cable set as optional accessory (GTZ3201000R0001)

Measurements per DIN EN 61010-031 may only be performed in

environments in accordance with measuring categories III and IV

with the safety cap attached to the test probe at the end of the

measurement cable.

In order to establish contact inside 4 mm jacks, the safety caps

have to be removed by prying open the snap fastener with a

pointed object (e.g. the other test probe).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gossen Metrawatt PROFITEST MXTRA in the language / languages: English as an attachment in your email.

The manual is 2,28 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gossen Metrawatt PROFITEST MXTRA

Gossen Metrawatt PROFITEST MXTRA User Manual - Dutch - 92 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gossen Metrawatt PROFITEST MXTRA Manual

Product: