590615
16
Zoom out
Zoom in
Previous page
1/71
Next page
16 GMC-I Messtechnik GmbH
Initial Start-Up – Setup
3 Initial Start-Up
3.1 Inserting Batteries or Rechargeable Batteries
Be certain to refer to chapter 9.2 regarding correct battery
installation.
Momentary battery voltage can be queried in the Info menu (see
chapter 6.3).
Attention!
!
Disconnect the instrument from the measuring circuit before
opening the battery compartment lid in order to replace the
batteries.
Operation with the Power Pack
(accessory for METRAHITX-
TRA, not included, see chapter 10.3)
Installed batteries are disconnected electronically if the NA X-TRA
power pack is used, and need not be removed from the
instrument.
If rechargeable batteries are used, they must be recharged
externally.
If the external power supply is switched off, the device is
automatically switched to battery operation without interruption.
3.2 Activation
Switching the Instrument On Manually
Ð Press the ON / OFF | LIGHT key until the display appears.
Power-up is acknowledged with a brief acoustic signal. As
long as the key is held depressed, all of the segments at the
liquid crystal display (LCD) are illuminated.
The LCD is depicted on page 13.
The instrument is ready for use as soon as the key is released.
Display Illumination
After the instrument has been switched on, background illumina-
tion can be activated by briefly pressing the ON / OFF | LIGHT key. Il-
lumination is switched back off by once again pressing the same
key, or automatically after approximately 1 minute.
Switching the Instrument On via PC (METRAHITX-
TRAOUTDOOR only)
The multimeter is switched on after transmission of a data block
from the PC, assuming the “irStb ” has been set to “ir on
(see chapter 6.4).
However, we recommend using the power saving mode: “ir off ”.
Note
Electrical discharge and high frequency interference may
cause incorrect displays to appear, and may disable the
measuring sequence.
Disconnect the device from the measuring circuit. Switch the
instrument off and back on again in order to reset. If the
problem persists, briefly dislodge the battery from the
connector contacts (see also chapter 9.2).
3.3 Setting the Operating Parameters
Setting Time and Date
See the “t iME ” and “dAtE ” parameter in chapter 6.4.
Display Modes for the Analog Display
Selection can be made from two different display modes
(see “A.diSP ” parameter in chapter 6.4).
Display Modes for the Digital Display
Selection can be made from two different display modes
(see “0.diSP ” parameter in chapter 6.4).
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gossen Metrawatt METRAHIT X-TRA at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gossen Metrawatt METRAHIT X-TRA in the language / languages: English as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gossen Metrawatt METRAHIT X-TRA

Gossen Metrawatt METRAHIT X-TRA User Manual - Dutch - 70 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info