590625
67
Zoom out
Zoom in
Previous page
1/74
Next page
GMC-I Messtechnik GmbH 67
Maintenance – Calibration
Replacing the Batteries
Attention!
!
Disconnect the instrument from the measuring circuit before open-
ing the battery compartment lid in order to replace the batteries.
Ð Set the instrument face down onto the working surface.
Ð Turn the slotted screw on the lid with the battery symbols
counterclockwise.
Ð Lift off the lid and remove the batteries from the battery com-
partment.
Ð Insert two new 1.5 V mignon batteries into the battery com-
partment, making sure that the plus and minus poles match up
with the provided polarity symbols.
Ð When replacing the battery compartment lid, insert the side
with the guide hooks first. Tighten the screw by turning it
clockwise.
Ð Please dispose of depleted batteries in accordance with envi-
ronmental protection regulations!
9.3 Fuse
Testing the Fuse
The fuse is tested automatically:
When the instrument is switched on with the rotary switch in
the A position
When the instrument is already on and the rotary switch is turned to
the A position
In the active current measuring range when voltage is applied
If the fuse is blown or has not been inserted, “FuSE” appears at
the digital display. The fuse interrupts the current measuring
ranges. All other measuring ranges remain functional.
Replacing the Fuse
If a fuse should blow, eliminate the cause of overload before plac-
ing the instrument back into service!
Attention!
!
Disconnect the instrument from the measuring circuit before
opening the fuse cover in order to replace the fuse!
Ð Set the instrument face down onto the working surface.
Ð Turn the slotted screw on the cover with the fuse symbol coun-
terclockwise.
Ð Lift off the cover and pry the fuse out using the flat side of the
fuse cover.
Ð Insert a new fuse. Make sure that the fuse is centered, i.e. be-
tween the tabs at the sides.
Ð When replacing the fuse cover, insert the side with the guide
hooks first. Tighten the screw by turning it clockwise.
Ð Dispose of the blown fuse with the trash.
Blown Fuse
fuse
A
DC
67


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gossen Metrawatt METRAHIT ULTRA BT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gossen Metrawatt METRAHIT ULTRA BT in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info