Manual Gossen Metrawatt METRAHIT ULTRA BT (page 31 of 74) (English)

590625

Zoom out

Zoom in

1/74

GMC-I Messtechnik GmbH 31

V/Hz/dB – Ω, Temperature, and A/Hz Measurements

5.1.2 Alternating Voltage and Frequency Measurement V AC and Hz

V AC with Selectable Low-Pass Filter, V AC + FiL and dB V AC

Note



See note in section 5.1.1.

Ð In accordance with the voltage or frequency to be measured,

turn the rotary switch to V~.

Ð Connect the measurement cables as shown.

The “⊥” connector jack should be grounded.

Voltage Measurement

Note



An intermittent acoustic signal warns the operator if the

measured value exceeds the upper range limit in the 600 V

range.

Make sure that a current measuring range (“A”) has not been acti-

vated when the multimeter is connected for voltage measure-

ment! If the fuse’s blowing limits are exceeded as a result of oper-

ator error, both the operator and the instrument are in danger!

Ð You can switch back and forth between voltage measurement

with and without low-pass filter.

Ð Repeatedly press the multifunction key FUNC | ENTER until unit

of measure V in appears at the main display, and FILTER ap-

pears in the header for measurement with low-pass filter.

Frequency Measurement

Ð Connect the measured quantity in the same way as for voltage

measurement.

Ð Manually select the measuring range for the voltage amplitude.

Ð Repeatedly press the multifunction key FUNC | ENTER until unit

of measure Hz appears at the display.

Lowest measurable frequencies and maximum allowable volt-

ages are listed in section 8, “Technical Data”,.

Note



Measurements performed close to the trigger level may result in

an incorrect display. If this is the case, select a smaller volt-

age measuring range.

In the case of measured values which are much higher than

the expected results, the input signal may be distorted. Per-

form measurement with activated 1 kHz low-pass filter in

this case.

Measurement with Low-Pass Filter

Attention!

Be aware of the fact that dangerous voltage spikes are not

displayed during this type of measurement (see also “Volt-

age Comparator”. We recommend measuring voltage with-

out the low-pass filter first, in order to be able to detect any

dangerous voltages.

A 1 kHz low-pass filter can be activate if required, in order to filter

out high frequency pulses of greater than 1 kHz, for example

when performing measurements at pulsed motor drives, i.e. un-

desired voltages of greater than 1 kHz can be suppressed.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gossen Metrawatt METRAHIT ULTRA BT in the language / languages: English as an attachment in your email.

The manual is 0,9 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gossen Metrawatt METRAHIT ULTRA BT Manual

Product: