512884
26
Zoom out
Zoom in
Previous page
1/40
Next page
240232
In case you were not successful in repairing the malfunctions in spite of
the above suggestion chart, call the nearest authorized service shop.
Repairing the failure arising from inappropriate connections or
use of the appliance is not covered by the guarantee, and the
repair expenses are paid by the customer.
* UKS: universal stability control - this function prevents excessive vibrations during spinning.
26
Failure Possible cause Remedy
Washing time is longer than
usual.
Time indicated on the
display is corrected during
the washing cycle.
Low temperature of inlet water.
Due to unevenly distributed
load, the machine has
activated the UKS*.
Low mains voltage.
There has been a failure in
the power supply.
Clean water sensor is
engaged.
Washing program time may be up
to 60% longer; however, this does
not imply a fault in the machine.
Washing time is extended by the
power supply down-time.
Time is prolonged for extra rinses.
ERROR 1
Program temperature not
reached (the machine
reports a failure)
Temperature sensor
disconnected from the
electronic circuit.
Turn off the appliance and wait for
a few seconds;
turn the appliance back on and
repeat the washing program.
If the failure is reported again, call a
service technician.
ERROR 4
Spinning rpm not reached
in the selected program (the
machine reports a failure)
rpm sensor disconnected
Motor overload due to too
high water level (manual
addition of water) or too big
laundry load
• Motor failure
Turn off the appliance and wait for
a few seconds;
turn the appliance back on and
repeat the washing program.
If the failure is reported again, call a
service technician.
ERROR 5
Motor operation interrupted;
or motor does not operate
(the machine reports a
failure)
Failure on motor regulation
(depending on model)
Turn off the appliance and wait for
a few seconds;
turn the appliance back on and
repeat the washing program.
If the failure is reported again, call a
service technician.
ERROR 6
Program temperature not
reached (the machine
reports a failure)
• Heater failure
Inlet water too cold
Manual addition of water
Turn off the appliance and wait for
a few seconds;
turn the appliance back on and
repeat the washing program.
If the failure is reported again, call a
service technician.
ERROR 9
Machine pumps water (the
machine reports a failure)
(only on some models)
Machine switched the Aqua-
stop protection system on
Disconnect the machine from mains
power and close water intake. Tilt the
machine carefully forward to let any
water collected at the bottom of the
machine to drain out. Reconnect the
machine and start the program. If the
failure occurs again, call nearest service.
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gorenje WS53123 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gorenje WS53123 in the language / languages: English as an attachment in your email.

The manual is 2,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info