603330
32
Zoom out
Zoom in
Previous page
1/132
Next page
32
WHI641A3B - WHI941A3B - WHI641A3XGB - WHI941A3XGB - WHI661A4X - WHI961A4X
To select the functions of the hood, simply touch the controls.
T1. Standby mode (the control panel off – all functions disabled) / ON (control panel switched on)
Note: After about a minute of inactivity (suction and lights), the hood will automatically switch to standby.
T2. ON/OFF lights
On certain models only (see drawing above):
press repeatedly to select the desired light intensity:
L1 : low light
L2 : medium light
L3 : high light
Press again to turn off the lights.
T3. ON/OFF Automatic operation
The hood automatically sets the suction speed (power) 1 to increase if the environmental conditions detected by the
hood sensor require it.
If there are no variations in the environmental conditions, after 10 minutes (if the hood is already in suction speed
(power) 1), the hood turns off.
Note: for a correct use of this function, first perform the "Setting of the parameters for Automatic Operation" (see
corresponding paragraph).
Note: During automatic operation, if the user acts on the other functions that adjust the speed, auto ventilation function
is switched off.
T4. Manual selection of the suction speed (power):
L4 : suction speed (power) 1
L5 : suction speed (power) 2
L6: suction speed (power) 3
Press again to turn off the hood (OFF).
Note: manual selection excludes any other suction related set function.
T5. ON/OFF Intensive suction speed (power) “POWER BOOST” (timed)
Note: After 5 minutes of operation the hood returns to its previous state.
T6*. (Only certain models ON/OFF intensive suction speed (power) “POWER BOOST x 2” (timed)
Note: After 5 minutes of operation, the hood goes back to the previous status.
T7. ON/OFF operation mode "Air refresh"
Every 50 minutes of inactivity, the suction speed (power 1 is turned on for 10 minutes.
T8. ON/OFF Delayed switch off of the suction speed (power) (approx. 30 minutes
Note: this function is available for the speeds that can be selected with button T4.
T9. Indicator and reset filter saturation
The button lights on automatically with steady light when it is necessary to perform the grease filter maintenance.
The button lights on automatically with flashing light when it is necessary to perform the charcoal filter maintenance.
After performing the maintenance, with the hood off and the button active, press the button for more than 3 seconds to
perform the reset of the filter saturation indicator; repeat the operation if necessary (for ex., when both filters are
saturated).
Activation of the charcoal filter saturation indicator
The saturation indicator of the charcoal filter is normally disabled. To activate it, proceed in the following manner:
With the display on (ON) and the suction off (OFF), press simultaneously the buttons T8 and T9 for more than 3
seconds; the button T9 lights on with steady light for approx. 5 seconds, to indicate the activation.
To disable it, repeat the operation; the button T9 will flash for approx. 5 seconds to indicate the disabling.
Setting of Automatic Operation parameters
For correct use of the automatic operation, perform "Hood Calibration" and "Selection of the hob".
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gorenje WHI641A3B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gorenje WHI641A3B in the language / languages: All languages as an attachment in your email.

The manual is 4,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info