512840
14
Zoom out
Zoom in
Previous page
1/24
Next page
Instructions for Use
Washing machine
141344
Thank you for your con dence in purchasing our washing machine, and congratulations on the
excellent choice.
Your new washing machine meets the requirements of modern treatment of laundry. It is rational in
the consumption of energy, water and washing agents.
Our appliances are friendly to the environment. Some of the materials may be recycled, others
deposited or decomposed. To avoid pollution of environment, once your appliance is no longer
useful, take it to your local authorized waste appliance dealer.
The appliance is intended exclusively for use in households. If the appliance is used for
professional purposes, for pro t, or for purposes beyond regular use in a household, or if appliance
is used by a person who is not a consumer, the warranty period equals the shortest warranty period
possible as stipulated by the relevant legislation.
Description of washing machine ..................................3
Cautions ..........................................................................4
Installation and connection ...........................................5
Operation .........................................................................8
Tips for washing and energy saving ..........................13
Cleaning and maintenance ..........................................14
Failures ..........................................................................17
Tables ............................................................................20
2
141344
Dimensions (w x d x h): 600 mm x 600 mm x 850 mm
Dimensions (w x d x h): 600 mm x 440 mm x 850 mm
Depth with door open: 106 cm / 88 cm (depending on model)
Weight (net): 90 kg / 79 kg (depending on model)
Nominal voltage: 230 V, 50 Hz
Power: 2300 W / 2200 W (depending on model)
Max. load: 7 kg / 6 kg / 4,5 kg (depending on model)
Power socket: (230 V, 50 Hz, 10 A)
Water pressure: min. 0,05 MPa, max. 0,8 MPa
Fuse: 10 A
1. Front panel
2. Detergent dispenser
3. Door
4. Filter lid
5. Adjustable legs
6. Water outlet hose
7. Water inlet hose
8. Mains power cable
3
Description of washing machine
Technical information
(depending on model)
141344
Be sure to remove transport brackets prior rst use of the appliance. Attempted operation of the
blocked machine may result in irreparable damage which is not covered by the manufacturer’s
warranty!
When connecting your washing machine to water supply, be sure to use brand new water inlet
hose and appropriate sealing gaskets (attached).
Do not locate the machine in a room with temperature below 0°C. Parts of the machine may be
damaged if frozen.
Install the washing machine in a perfectly horizontal position, on solid at concrete oor.
Follow the instructions for correct installation and water and mains connections.
Never immerse the end of the drain hose into the draining water.
Prior starting the washing cycle lock the door by pressing them at the designed spot.
Door may not be open during the washing cycle.
Use only detergents and softeners for machine wash. Manufacturer may not assume
responsibility for any damage and eventual discoloring of gaskets and plastic components as a
consequence of incorrect use of bleach and/or coloring agents.
For removal of lime residues use such agents with added anti-corrosion agents. Follow the
manufacturer’s instructions. Finish the lime removal by multiple rinsing to remove completely
eventual acid residues.
Never use detergents containing solvents, since there is a danger of creating toxic gasses which
may damage the machine and result in ignition or explosion.
Upon completion of washing operation close the water faucet.
Before any transport block the machine by inserting at least one transport blocking rod. Prior this
operation disconnect the appliance from the mains power!
Rating plate with basic information is located above the opening of the machine.
The warranty shall not apply to consumables (bulbs), minor discoloration or deviations of color,
increased noise level as a consequence of appliance age, which does not affect appliance
functionality, and aesthetical de ciencies which do not affect appliance functionality or safety.
Before connecting the appliance read these instructions carefully. Repairing the failure
arising from inappropriate connections or use of the appliance is not covered by the
guarantee.
The symbol on the product or on its packaging indicates that this product may not
be treated as household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will help prevent potential
negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of thisproduct. For more
detailed information about recycling of this product, please contact your local city
of ce, your household waste disposal service or the shop where you purchased the
product.
4
Cautions
141344
In removing the wrapping be careful not to damage the
appliance with a sharp object.
Before connecting the appliance, let it warm up to room
temperature (wait for two hours).
Our appliances are packed in environmentally friendly
materials which may be recycled, deposited or decomposed
without any threat to the environment.
To this end all wrappings are marked accordingly.
Move the pipes.
Loosen screws A at the rear of the machine (Fig. 1).
Remove the brackets B (Fig. 1) and slide them into the groove
on the blocking rod (Fig. 2) - the right one should be turned
around.
Use the brackets to rotate blocking rods for 90° and pull them
out.
Close the openings with attached plastic pegs.
Save transport brackets for eventual later use.
Be sure to remove the transport brackets prior rst
use, otherwise the appliance may be permanently
damaged. In such cases the warranty conditions are
void.
Fig. 1 Fig. 2
Put the appliance in horizontal position by turning the
adjustable legs.
The legs are adjustable up to +/- 1 cm.
After the adjustment tighten the nuts rmly (A) - towards
the bottom of the machine!
Vibrations, moving of the appliance and loud operation
due to incorrect setting of the adjustable feet shall not
be covered by this warranty.
The appliance should be placed on a surface with
concrete base; the surface should be dry and clean in
order to prevent slipping. The adjustable feet should
also be cleaned before installation.
Package removalPackage removal
Removal of transport
brackets
Removal of transport
brackets
Leveling the applianceLeveling the appliance
5
Installation and connection
141344
If you have a tumble dryer of the same dimensions, you can
place it on top of the washing machine.
To ensure correct operation of the appliance, water
pressure inlet must be between 0,05 and 0,8 MPa.
Minimum water pressure can be established by
measuring the quantity of poured out water. 3 litres of
water must be poured out from completely opened tap
in 15 seconds.
Insert the gasket with screen into the water inlet hose thread
Screw the hose thread to the water faucet
In case of hot and cold water connection, connect one hose to
cold and other to hot water faucet as marked at the rear of the
appliance (letters C and H) (C - cold; H - hot)
Fix the outlet hose to run into the sink or the bathtub, or
connect it directly to the wall drain outlet (diameter min. 4 cm).
Wall drain must be installed properly and must enable
occasional cleaning.
Fasten the outlet hose support with a piece of rope led through
the hose elbow, to prevent the hose from slipping to the oor.
The end of outlet hose should be placed between minimum 60
cm and maximum 100 cm above the oor level.
Plug the mains power cable to the wall mains socket.
Required voltage and other information are written on the
rating plate above the door opening of the machine.
The wall socket must be accessible at all times and
must be equipped with an earth lead (in accordance
with the local safety regulations).
The permanent connection must be tted by an
authorized personnel only.
Water inlet connectionWater inlet connection
Water outlet connectionWater outlet connection
Connect the appliance to
the mains supply
Connect the appliance to
the mains supply
6
141344
Damaged mains power cable may be replaced only by
the producer or his authorized personnel.
Never plug the appliance into the electric shaver socket
or hair dryer socket.
7
141344
A - program selector
B - pump stop knob
C - START/PAUSE knob
Signal LED’s: - ON/OFF (orange)
- pump stop/failure
(green)
8
Program selector Basic programs Partial programs
Cotton
Pre-wash
Short program
Rinse
Synthetics
Short program
Softening
Delicate Pumping water
Wool Spinning
Operation
141344
Open the door of the machine
Load the laundry into the drum
Close the door
Open the water inlet faucet
Push the ON/OFF button and select the program
Add washing and treatment agents (detergent and softener)
Start the operation by pushing the START knob (C)
- Open the door of the machine.
Door is opened by pulling the handle (lever) on the right hand
side of the door towards you.
- Sort the laundry by the type of fabrics.
Do the buttons and zippers, tie the strings and pull out
the pockets.
Very delicate laundry should be put in a special
protective sack.
It is suggested to load the drum with items of different
sizes.
Pay attention to the labels on the clothes, indicating
the recommending washing mode (see table of
textile treatment symbols on the last page of these
instructions).
- Load the laundry into the drum.
Check that the drum is empty.
- Close the door of the appliance.
- Open the water inlet faucet.
- Push the ON/OFF button and select washing program.
Program is selected by turning the program selector (A) from the
“0” position to the desired washing program. The ON/OFF signal
LED starts ashing. The program selector (A) may be turned in
both directions, and the appropriate program selected according
to the type of laundry washed and the required washing
temperature (see Program Chart for help). You may select basic
or partial programs.
Selected program may be changed at random prior pushing the
START button (C).
- Selection of basic programs (
, , , )
Basic programs represent integral programs containing all
washing stages, including softening and spinning (see Program
Chart). They are selected by turning the program selector to the
appropriate position.
Cotton: whites/colored
Normally stained cotton and ax bed linen and underwear, table
Washing procedureWashing procedure
Washing machine
operation
Washing machine
operation
9
141344
cloth, bathroom towels, top garments, etc.
For less stained laundry of this type, use short program. It saves
energy and washing time.
For heavily stained permanent press use the program with the
pre-wash
.
Synthetics
Normally stained shirts, blouses and other polyester and
polyamide garments, or a mixture of these fabrics with cotton.
For less stained laundry of this type, use short program. It saves
energy and washing time.
Delicate
This is a program for delicate fabrics (dresses, skirts, blouses)
and curtains.
Wool
Especially gentle program for washing wool and garments made
from mixture of other fabrics with wool, appropriately marked for
machine washing.
- Selection of additional function
Pump stop
This function is switched on after the selection of a basic
program by pressing the
knob (B). It may also be switched
on during the operation, prior last rinse. Indicator LED above
the washing cycle symbol is lit.
The function is switched off by pressing the same knob again
- signal LED is off.
The program stops at the end of last rinse, prior spinning:
laundry remains soaked in water and prevents crease, if
you are unable to remove it from the drum immediately after
the end of washing cycle. Indicator LED above the knob is
ashing.
The selected program is completed by pushing the START
button (C), but you may also apply additional programs
(pumping or spinning), but you must rst return the program
selector to the “0” position for at least one second, prior
selecting any of the additional programs.
When program continues, indicator LED above the knob goes
off.
- Selection of partial programs (
, , , )
These are independent programs and may be used when you do
not need the entire washing program. In case you would like to
use more additional programs in a sequence, you must turn off
the appliance prior any new program selection (turn the program
10
141344
selector (A) to “0” for at least one second).
Rinse
Independent program for rinsing delicate laundry, without
intermediate spinning and with short nal spin. You may use it for
rinsing manually washed delicate laundry or for extra rinsing for
people with skin sensitive to detergents.
Softening
This program is intended for softening, bleaching or impregnating
of washed laundry. It is completed with spinning at max. 1000
RPM.
Pumping the water out
Use it when the washing program was interrupted or if pump stop
function was engaged, and you only wish to pump the water out
of the drum, without spinning.
Spinning
Aggressive spinning for non-delicate laundry at high spin RMP.
- Adding washing and softening agents
(see Tips for washing and energy saving)
• pre-wash compartment
• main wash compartment
• softener compartment
Washing detergent may be added directly into the drum, using
the measuring vessel.
When adding softener, be careful to ll the dispenser
only up to the marked level.
Be sure to close the detergent dispenser when
opening/closing the appliance door.
Push the START button (C). The ON/OFF LED stops ashing,
the machine starts operating after a few seconds. If the door
is not properly closed after starting the operation, the ON/OFF
LED starts ashing again after a few seconds. When you close
the door, the machine initiates the selected program.
In case you would like to alter the washing program after the
initiated washing operation, turn the program selector for one
second to the position “0”, followed by the selection of a new
program. Switching the machine off deletes any previously
Start the operationStart the operation
11
141344
selected additional functions (i.e. PUMP STOP) , so they
have to be reactivated.
- End of operation
Flashing START/STOP LED indicates that the program was
completed.
Extract the laundry from the drum and remove any alien
objects from the door gasket.
Leave the door ajar to allow the interior to dry.
Close the water inlet faucet.
Switch the machine off by turning the program selector to
position “0”.
Pull the power lead from the socket and cut the power supply
from the mains.
By the user
Selecting Pump stop function
Program is stopped when it comes to the ‘PUMP STOP’
stage (if this function had been previously selected). Drum door
remains closed all the time. Indicator LED above the ‘Pump
stop’ function starts ashing. Washing procedure is continued by
pressing the START knob (C).
Own (physical) interruption
You may also stop the program by turning the program selector
to the position “0”. If there is water in the drum select one of
additional programs (pumping, spinning) to empty the water and
terminate the program.
Pause knob
By pressing the PAUSE knob (C) program may be suspended
at any time. After certain time you may open the door if there is
no water in the drum, otherwise this is not possible. Program is
continued by pressing the START knob (C).
Failures
Program is suspended in case a failure occurs. Signal LED’s
are ashing (see cf. Troubleshooting).
Power failure
At electric cutout the program is interrupted, however, after the
power supply has been re-established, the program operation
automatically proceeds.
If a power failure occurs when the drum is still full of
water, be careful not to open the door before you pump
the water out.
InterruptionsInterruptions
12
141344
Before washing sort out the laundry according to the type, degree of dirtiness and color fastness.
Prior selecting the washing program consult the sewn tab with information on a particular piece
of laundry (see Maintenance chart on the last page).
Wash separately the new colored textile products for the rst time.
Wash heavily soiled laundry in small quantities and add more detergent.
Treat stubborn stains with special stain remover, it will save energy.
With lightly stained laundry select washing program without pre-wash, use short program and
select lower washing temperature. This way you may save up to 50% of energy.
Avoid washing too little quantities of laundry because of energy saving and for better
performances of the appliance.
The largest allowed quantity of dry laundry is indicated in the Program chart.
Before washing empty the pockets, close zip fasteners, and remove any metal fasteners or
badges that might clog the drain or damage the laundry or drum interior.
Loosen the stacked laundry prior inserting it into the drum.
Use only detergents for machine wash.
Add powder or liquid detergents according to the manufacturer’s instructions.
If water hardness level exceeds 14°dH degrees, the use of water conditioner is required. Any
damage to the heater due to failure to use a water conditioning agent shall not be covered by
this warranty.
Chlorine-based whitening agents are not recommended, as it can damage the heater.
• If you do not apply the program which includes the pre-wash
feature, you may add washing detergent directly into the drum.
If you use thick liquid softener it is recommended to dilute
it with water, to prevent clogging of dispenser compartment
ducts.
Washing machine is equipped with the dispenser partition
gate, so you may pour liquid detergent also into the central
compartment. If you use powder detergent the gate is lifted up,
and in case of liquid detergent it is slid down.
Liquid detergents are intended for main wash only, without
pre-wash.
Insert particularly delicate linen (stockings, delicate female
underwear, etc.) into the special bag.
13
Hardness
scale
Degree of hardness
°dH(°N) m mol/l °fH(°F) p.p.m.
1 - Soft < 8,4 < 1,5 < 15 < 150
2 - Medium 8,4 - 14 1,5 - 2,5 15 - 25 150 - 250
3 - Hard > 14 > 2,5 > 25 > 250
In case of hard water add detergent according to the Chart for
degree 1 and add appropriate quantity of water softener (see
manufacturer’s instructions).
Tips for washing and energy saving
141344
Disconnect the washing machine from the mains
before cleaning!
The casing should be cleaned with soft cloth and mild
detergent.
The interior of the drum and the door gasket is cleaned by
washing at 60°C without laundry and adding half quantity of
detergent.
If necessary, clean the detergent dispenser. Pull it out from its
casing completely by pressing the ap (see Fig.).
If necessary, clean the cover of the bung under the running
water.
High spin RPM leave less moisture in laundry which dries out
much quicker in the tumble dryer, thereby saving energy.
Do not put clods of detergent into the soap dispenser
as the tube in the washing machine may clog.
14
Cleaning and maintenance
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gorenje WA61102 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gorenje WA61102 in the language / languages: English as an attachment in your email.

The manual is 1,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info