512798
12
Zoom out
Zoom in
Previous page
1/24
Next page
Instructions for Use
Washing machine
231991
Dimensions (w x d x h): 600 mm x 600 mm x 850 mm
Dimensions (w x d x h): 600 mm x 440 mm x 850 mm
Depth with door open: 106 cm / 88 cm (depending on model)
Weight (net): 90 kg / 76 kg (depending on model)
Nominal voltage: 230 V, 50 Hz
Power: 2300 W / 2200 W (depending on model)
Max. load: 7 kg / 6 kg / 4,5 kg (depending on model)
Power socket: (230 V, 50 Hz, 10 A)
Water pressure: min. 0,05 MPa, max. 0,8 MPa
Fuse: 10 A
1. Front panel
2. Detergent dispenser
3. Door
4. Filter lid
5. Adjustable legs
6. Water outlet hose
7. Water inlet hose
8. Mains power cable
3
Description of washing machine
Technical information
(depending on model)
231991
Be sure to remove transport brackets prior rst use of the appliance. Attempted operation of the
blocked machine may result in irreparable damage which is not covered by the manufacturer’s
warranty!
When connecting your washing machine to water supply, be sure to use brand new water inlet
hose and appropriate sealing gaskets (attached).
Do not locate the machine in a room with temperature below 0°C. Parts of the machine may be
damaged if frozen.
Install the washing machine in a perfectly horizontal position, on solid at concrete oor.
Follow the instructions for correct installation and water and mains connections.
Never immerse the end of the drain hose into the draining water.
Prior starting the washing cycle lock the door by pressing them at the designed spot.
Door may not be open during the washing cycle.
Use only detergents and softeners for machine wash. Manufacturer may not assume
responsibility for any damage and eventual discoloring of gaskets and plastic components as a
consequence of incorrect use of bleach and/or coloring agents.
For removal of lime residues use such agents with added anti-corrosion agents. Follow the
manufacturer’s instructions. Finish the lime removal by multiple rinsing to remove completely
eventual acid residues.
Never use detergents containing solvents, since there is a danger of creating toxic gasses which
may damage the machine and result in ignition or explosion.
Upon completion of washing operation close the water faucet.
Before any transport block the machine by inserting at least one transport blocking rod. Prior this
operation disconnect the appliance from the mains power!
Rating plate with basic information is located above the opening of the machine.
The warranty shall not apply to consumables (bulbs), minor discoloration or deviations of color,
increased noise level as a consequence of appliance age, which does not affect appliance
functionality, and aesthetical de ciencies which do not affect appliance functionality or safety.
The appliance is manufactured in compliance with all relevant safety standards; however, it is
recommended that persons with impaired physical, motional, or mental abilities, or persons with
inadequate experience and knowledge, do not use the appliance without due supervision. The
same recommendation applies to minors using the appliance.
Before connecting the appliance read these instructions carefully. Repairing the failure
arising from inappropriate connections or use of the appliance is not covered by the
guarantee.
The symbol on the product or on its packaging indicates that this product may not
be treated as household waste. Instead it shall be handed over to the applicable
collection point for the recycling of electrical and electronic equipment. By
ensuring this product is disposed of correctly, you will help prevent potential
negative consequences for the environment and human health, which could
otherwise be caused by inappropriate waste handling of thisproduct. For more
detailed information about recycling of this product, please contact your local city
of ce, your household waste disposal service or the shop where you purchased the
product.
4
Cautions
231991
In removing the wrapping be careful not to damage the
appliance with a sharp object.
Before connecting the appliance, let it warm up to room
temperature (wait for two hours).
Our appliances are packed in environmentally friendly
materials which may be recycled, deposited or decomposed
without any threat to the environment.
To this end all wrappings are marked accordingly.
Move the pipes.
Loosen screws A at the rear of the machine (Fig. 1).
Remove the brackets B (Fig. 1) and slide them into the groove
on the blocking rod (Fig. 2) - the right one should be turned
around.
Use the brackets to rotate blocking rods for 90° and pull them
out.
Close the openings with attached plastic pegs.
Save transport brackets for eventual later use.
Be sure to remove the transport brackets prior rst
use, otherwise the appliance may be permanently
damaged. In such cases the warranty conditions are
void.
Fig. 1 Fig. 2
Put the appliance in horizontal position by turning the
adjustable legs.
The legs are adjustable up to +/- 1 cm.
After the adjustment tighten the nuts rmly (A) - towards
the bottom of the machine!
Vibrations, moving of the appliance and loud operation
due to incorrect setting of the adjustable feet shall not
be covered by this warranty.
The appliance should be placed on a surface with
concrete base; the surface should be dry and clean in
order to prevent slipping. The adjustable feet should
also be cleaned before installation.
Package removalPackage removal
Removal of transport
brackets
Removal of transport
brackets
Leveling the applianceLeveling the appliance
5
Installation and connection
231991
- End of operation
Flashing START/STOP LED indicates that the program was
completed.
Extract the laundry from the drum and remove any alien
objects from the door gasket.
Leave the door ajar to allow the interior to dry.
Close the water inlet faucet.
Switch the machine off by turning the program selector to
position “0”.
Pull the power lead from the socket and cut the power supply
from the mains.
By the user
Selecting Pump stop function
Program is stopped when it comes to the ‘PUMP STOP’
stage (if this function had been previously selected). Drum door
remains closed all the time. Indicator LED above the ‘Pump
stop’ function starts ashing. Washing procedure is continued by
pressing the START knob (C).
Own (physical) interruption
You may also stop the program by turning the program selector
to the position “0”. If there is water in the drum select one of
additional programs (pumping
, spinning ) to empty the
water and terminate the program.
Pause knob
By pressing the PAUSE knob (C) program may be suspended
at any time. After certain time you may open the door if there is
no water in the drum, otherwise this is not possible. Program is
continued by pressing the START knob (C).
Failures
Program is suspended in case a failure occurs. Signal LED’s
are ashing (see cf. Troubleshooting).
Power failure
At electric cutout the program is interrupted, however, after the
power supply has been re-established, the program operation
automatically proceeds.
If a power failure occurs when the drum is still full of
water, be careful not to open the door before you pump
the water out.
InterruptionsInterruptions
12
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gorenje WA1067 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gorenje WA1067 in the language / languages: English as an attachment in your email.

The manual is 2,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info