308224
22
Zoom out
Zoom in
Previous page
1/32
Next page
300107
22
Failure Possible cause Remedy
Greasy wads appear on
the laundry.
Too little detergent (laundry was
very greasy).
Wash the laundry again.
Add more detergent for such soiled
laundry, or use liquid detergent.
Laundry is stained after
washing.
You used liquid detergent or
detergent for colored laundry
which does not contain whitener.
Use the detergent containing
whitener.
White powdery residues
on the laundry.
It is not the consequence of bad
rinsing, but because of neo-
phosphate detergents containing
non soluble components
(zeolites) for water softening.
Such substances may be
deposited upon the laundry.
Immediately rinse the laundry once
again.
Use liquid detergents which do not
contain zeolites.
Try removing the residues with the
brush.
Detergent residues in the
dispenser.
Low water ow pressure.
Some detergents may stick to
the dispenser rather hard if it
is wet.
Clean the inlet pipe lter net.
In case of low water pressure
increase water level.
• Wipe the dispenser prior loading
detergent.
Softener is not completely
rinsed, or water is left in
the dispenser dish.
Sucking cover is not correctly
positioned or is clogged.
Clean the dispenser and rmly x
the cover to its place.
Unpleasant smell in the
washing machine drum.
Remains of fabrics, washing
agent and softener in the lter.
Development of germs
Check whether the lter is clean.
Run the auto-clean (SterilTub)
program (see chapter: selecting
additional functions)
Washing time is longer
than usual.
Time indicated on the
display is corrected during
the washing cycle.
Low temperature of inlet water.
The machine switched on
the UKS* system because of
uneven laundry load.
Low mains voltage.
There has been a failure in the
power supply.
Washing program time may be up
to 60% longer; however, this does
not imply a fault in the machine.
Washing time is extended by the
power supply down-time.
FAILURE 1
Program temperature not
reached (the machine
reports a failure F1 - the
LEDs periodically ash
once)
Temperature sensor
disconnected from the electronic
circuit.
Turn off the appliance and wait for
a few seconds;
turn the appliance back on and
repeat the washing program.
If the failure is reported again, call a
service technician.
FAILURE 4
Spinning rpm not reached
in the selected program
(the machine reports
a failure F4 - the LEDs
periodically ash four
times)
rpm sensor disconnected
Motor overload due to too high
water level (manual addition of
water) or too big laundry load
• Motor failure
Turn off the appliance and wait for
a few seconds;
turn the appliance back on and
repeat the washing program.
If the failure is reported again, call a
service technician.
22


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gorenje wa 72145 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gorenje wa 72145 in the language / languages: English as an attachment in your email.

The manual is 2,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info