354092

Gorenje r 1446 labl Manual

6
Zoom out
Zoom in
Previous page
1/7
Next page
Instructions for Use
16
Changing the Direction of Opening the Door
If you find the direction of opening the door on your appliance
inconvenient, you can change it. Holes on the opposite side
have already been prepared in the factory.
 Unscrew the kick-plate and remove it by pushing
downwards.
 Unscrew the lower hinge and take off the door together with
the upper hinge washer.
 Unscrew the upper hinge fastener and fix it on the opposite
side of the appliance.
 Take off, change and replace the door hinge fixture and the
fixture plugs.
 Put the door with the upper hinge washer on the upper hinge
fastener.
 Fix the lower hinge with washer on the new position.
 Replace the cover plate of the lower hinge to the opposite
side of the kick-plate and fix it to the appliance.
 In case your appliance is equipped with a handle mounted
on the side of the appliance, take it off and replace it on the
other side.
Some screws are covered with caps. Take them off before
undoing the screws.
 Check the gasket, it shouldn't be creased and it should seal
well.
Should the seal not adhere to the casing of the appliance
perfectly, it will have to be heated from a suitable distance
(by means of hair drier, for example) and lightly stretched to
the required height.
Changing the Direction of Opening the Door on the
Frezing compartment
 Unscrew the blocking element and the hinge of the Frezing
compartment and take off the door.
 Plug the holes with plastic caps provided.
 Turn the door for 180° and replace it on the opposite side of
the Frezing compartment. Fix the hinge and the blocking
element of the door (position of holes already provided).
1 Upper hinge fastener 5 Kick plate or control panel
2 Upper hinge washer 6 Cover plate of the lower hinge
3 Lower hinge 7 Fixture plug of the door hinge
4 Lower hinge washer 8 Door hinge fixture
9 Frezing compartment 11 Door hinge
10 Blocking element
Maintenance and Cleaning
Automatic Defrosting of the Refrigerator
There is no need to defrost the refrigerator, because ice
depositing on the inner back wall is defrosted automatically.
Ice is depositing on the inner back wall during the compressor
operation; later on, when the compressor is not operating ice is
defrosting and water drops collect and drain through the outlet
in the inner back wall into the drain pan situated above the
compressor, from where it evaporates.
Manual Defrosting of the Frezing Compartment
When the frost and ice layer in the Frezing compartment is 3-5
mm thick, you should clean the freezer.
 Turn the thermostat knob to STOP (0) position and
disconnect the power supply. Empty the compartment and
take care that the packages remain frozen.
 Use a suitable cloth to dry the defrost water collected during
defrosting on the bottom of the Frezing compartment.
Leave the door of the compartment open to accelerate
defrosting.
 Avoid using defrosting sprays, as they may cause damage
to the plastic parts and may be hazardous to health.
Cleaning the Appliance
Disconnect the power supply before cleaning the
appliance. Do not use coarse or aggressive cleaning agents
as you can damage the surface. Be careful to remove any
cleanser agent remaining after cleaning.
 Clean the exterior with water and detergent.
Varnished surfaces are cleaned with soft cloth and an
alcohol based cleaning agent (for example glass cleaners).
You may also use alcohol (ethanol or isoprophylic alcohol).
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gorenje r 1446 labl at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gorenje r 1446 labl in the language / languages: English as an attachment in your email.

The manual is 0,28 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info