326973
18
Zoom out
Zoom in
Previous page
1/18
Next page
179732
Instructions for use, installation and connection
19
Caution: In case you fail to set the current time within 7
seconds following the plugging of the appliance to mains
power, it will start running automatically. If you now turn button
2 in the ‘+’ direction, current time stops flashing, but symbol
S3 is still flashing. You can now set the current time as follows:
Turn button 1 to the position "current time" and then back to
"manual".
Set current time with button 2 (symbol S3 is off, symbol S1
is on).
Repeat the same procedure in case of power failure, or in case
of changing the time of day.!
Button 1 in position ‘current time’ serves exclusively for
displaying current time, and not for changing it!
Setting the conventional (manual) operation
Turn the button 1 to the position "manual". All actual running
programs are hereby cancelled (the symbol S3 is deleted if it
was active). Symbol S1 becomes active (if it was not already
on), which means that the clock is set to the conventional
(manual) mode of operation.
Semi-automatic operation with the defined period
Turn button 1 to the position "period of operation". The display
indicates 0 00 and the symbol S1 is on. Set the desired period by
turning button 2 to the position "+" or "-". The symbol S3 appears.
The period of operation may be selected in steps of 1 minute.
Maximum possible period to be set is 10 hours.
Once the desired period of operation is selected, the time
countdown starts after the 7 second lapse. If button 1 remained in
the position "period of operation" the display indicates the
countdown time.
The remaining time may be checked by turning button 2, while
button 1 must remain in the position "period of operation".
The expiry of the set period is signaled by the alarm, which is
switched off automatically after 7 minutes, if it was not switched off
before by turning button 1 into any position other than the present
one. The symbol S1 is off and the symbol S3 flashes. In this
moment the oven is switched off.
After turning the button 1 into the position "manual" the symbol S3
turns off and the symbol S1 reappears. The clock is set to
conventional (manual) mode.
If you wish to terminate roasting the oven must be switched
off!
Semi-automatic operation with the end of operation
Turn button 1 to the position "end". The display indicates the
current time. Set the desired end of operation time by turning
button 2 towards the position "+" or "-" (naturally, the end time
must be greater than the current time). The symbol S3
appears. The display returns to read current time 7 seconds
after the setting process is completed.
Once the current time reaches the preset end of operation
time, this is signaled by the sound alarm, which is switched off
automatically after 7 minutes, if it was not switched off before
by turning button 1 to any direction. The symbol S1 is off and
symbol S3 flashes. In this moment the oven is switched off.
After turning button 1 into the position "manual" the symbol S3
turns off and the symbol S1 reappears. The clock is set to
conventional (manual) mode.
If you wish to terminate roasting the oven must be
switched off!
Automatic operation with the preset period and the
end of operation
Turn button 1 to the position "period of operation" and by
turning button 2 towards "+" or "-" set the period of cooking.
Then turn button 1 into the position "end" and the display
indicates the nearest possible end of operation time. Set the
desired end of operation time by turning button 1 towards "+"
or "-". The symbol S1 is off if the end time is greater than the
current time + the preset period of operation.
The oven starts operating automatically according to the preset
times.
Example
Current time = 12:00, operation interval was set at 1:30 and the
end of operation at 14:00. This means that the oven will start
operating at 12:30.
Errors in setting the time
If the selected end time falls shorter than the current time +
period of operation, this is signaled by the sound alarm and the
flashing symbol S3. Preset times have to be corrected and
adjusted (the best procedure is to turn button 1 into the
position "manual" and repeat the complete procedure).
Alarm timer
To activate the timer, turn button 1 to the position "timer". This
timer functions only as a warning signal and does not switch off
the oven.
Set the desired time by turning button 2 towards "+" or "-".
Symbol S2 is on.
Once the desired alarm time is selected, the time countdown
starts after the 7 second lapse. If button 1 remained in the
position "timer" the display indicates the countdown of preset
time.
The remaining time may be corrected with button 2, while
button 1 must remain in the position "period of operation".
The expiry of the set period is signaled by the alarm, which is
switched off automatically after 7 minutes, if it was not
switched off before by turning button 1 in any position other
than the actual one. The symbol S2 is off.
Button (1) in the position of current time
This position is neutral and indicates current time. It is used in
case you wish the current time to be indicated on the display.
The clock is for example set to automatic operation. If button 1
is set to the position "end" the display reads the end of
operation time, and if button 1 is turned to the position "current
time" the display will read current time.
Sound alarm volume
When all functions are off (only the current time is displayed) it
is possible to select 3 different volume settings of the sound
signal. Turn button 1 to the position "manual" and wait for 7
seconds. If button 2 is turned prior the expiry of this period, the
current time will be altered! Next, turn button 2 towards "-"
and keep it in this position. The first volume level is sounded.
Release button 2 and turn again towards "-" for the next
volume level, etc.
The last selected level is stored as default. Volume level may
be reset anytime.
Deleting all timer adjustments
All the time settings except the alarm timer may be deleted at
any time by turning button 1 to the position "manual".
Preset programs are automatically cancelled and the clock
returns to the conventional (manual) mode.
Using the clock in combination with oven
To use the clock in combination with oven, the first step is
to switch the oven on and set the desired baking mode
and the temperature. Only after that you may proceed
setting the clock functions. After the completion of baking
switch the oven off.
WE RESERVE THE RIGHT TO ALTER THE SPECIFICATIONS WITH NO INFLUENCE ON THE
OPERATION OF THE APPLIANCE.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gorenje k 7708 e at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gorenje k 7708 e in the language / languages: English as an attachment in your email.

The manual is 1,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info