335437
14
Zoom out
Zoom in
Previous page
1/18
Next page
Instructions for use, mounting and connection
53
Control elements
Once the glass ceramic hob is connected to the
mains (including the power failure), the appliance
will perform the process of initial synchronization
with the exterior environment, in order to provide
the most efficient sensor function and render the
best control.
After the successful accommodation to the
environment had been completed, the indicators
show the mark "-" for a moment which eventually
disappears.
The sound signal confirms the appliance is now
ready for use.
Do not place any objects upon the sensor surface
during the accommodation period, otherwise you
may provoke error mode. In such cases the
process is interrupted and all indicators display
the symbol ''F''. The hob fails to respond to
commands.
The hob is equipped with electronic sensors
which are switched on by touching or pressing the
relevant sensor surface with your fingertip.
Each sensor reaction is confirmed by the beep.
Be sure to always touch only one sensor at the
time, and for a very brief period of time
(approximately 1 second). If more than one
sensor is pressed at the same time the relevant
command is not accepted. If the touch is
prolonged it provokes error mode and the
appliance is switched off.
Do not place any objects upon the sensor surface
(error mode) nor any hot dishes which may
damage the sensors. Keep the sensor surface
clean at all times.
Switching the hob on
When the hob is turned off all the hotplates are
off and indicator LED's are off.
To switch the hob on, touch the ON/OFF sensor.
The hob is activated and the hob #4 power
display indicates flashing »0« for a period of 10
seconds. Other hob indicators are not illuminated.
In case the main ON/OFF sensor was pressed for
more than 2 seconds, the hob is switched off and
needs to be restarted. Using the (+) or (-) sensor
you may select the desired cooking power in 10
seconds following the switch on or selection of a
particular hotplate.
Selecting the particular hotplate
Once the hob is switched on with the ON/OFF
sensor, activate the hotplate selection sensor to
select the next hotplate in the clockwise direction,
always starting with hotplate #4. The indicator
flashes 10 seconds after the hotplate and its
power setting are selected. Active hotplate is
indicated by flashing power setting. By touching
the (+) sensor you select setting "9" and activate
automated cooking mode. Current setting may be
reduced by touching the (-) sensor in short
intervals. Prolonged pressing speeds up the
setting reduction. If you switch the hotplate on by
touching the (-) sensor, the power selection
indicates "4". This setting may then be increased
or reduced by pressing either (+) or (-) sensor
and select the desired heating power.
If the hotplate selection sensor is touched once
again, you select the next hotplate in clockwise
direction, and this is signaled by flashing of the
indicator.
If only one hotplate is activated, by pressing the
hotplate selection sensor this hotplate is selected
directly. In case more than one hotplate is active,
the first one to be activated is always hotplate
#4.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gorenje ect 680 al at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gorenje ect 680 al in the language / languages: English as an attachment in your email.

The manual is 1,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gorenje ect 680 al

Gorenje ect 680 al User Manual - German - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info