335437
9
Zoom out
Zoom in
Previous page
1/18
Next page
Instructions for use, mounting and connection
48
Switching the extended hotplate
rings on (hotplates 2 and 4)
Switch the relevant hotplate ( 2 or 4) and
consequently switch the extended hotplate ring by
pressing the relevant sensor (see the control
element board illustration). The LED signal lamp
above the indicator displays the extended ring is
on. Now select the random heating power for
both hotplate rings together. Extended ring may
be switched off either by consequent pressing the
sensor or by reducing the heating power to "0",
as well as by simultaneous pressing of both the
(-) and (+) sensor. It may of course be switched
off also by switching off the entire hob.
Switching the second hotplate ring
on
The rear right hotplate (4) is equipped with the
extended hotplate ring, which is switched on by
pressing the special second ring sensor. The
signal lamp above the indicator displays the ring
is on.
Switching the third hotplate ring on
(certain models)
The front left hotplate (2) is equipped with two
extended hotplate rings. To switch the second
ring on, press the special second ring sensor (top
left). The LED signal lamp above the indicator
displays the ring is on. To switch on the third ring
press the same sensor once again, another LED
signal lamp is on. Both extended rings are
switched off by repeated pressing the sensor.
They may also be switched off by switching off
the relevant hotplate or the entire hob.
Blocking the hob operation
This function mode is intended as a protection
against accidental start or change of heating
power by children or pets. The hob may be
blocked by pressing the relevant sensor for about
3 seconds, illuminating the LED signal lamp
above the sensor. The hob may be blocked both
with the hob switched on or off. The functioning of
the complete hob is blocked, except for the main
hob switch and the blocking sensor. In the
blocked mode all hotplates may be switched off
only by pressing the main ON/OFF hob sensor,
while the blocked mode remains active. To
activate a particular sensor in the blocked mode,
the signal lamp goes on for a few seconds. If a
particular hotplate is in timer automatic mode, the
countdown proceeds normally and the hotplate is
switched off at the expiry of preset time, signaling
the end by the triple beep.
The blocked mode may be switched off at
anytime by pressing the sensor. Short beep
confirms the action, and the LED signal lamp
goes off.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gorenje ect 680 al at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gorenje ect 680 al in the language / languages: English as an attachment in your email.

The manual is 1,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gorenje ect 680 al

Gorenje ect 680 al User Manual - German - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info