Manual Gorenje ect 600 e (page 10 of 13) (English)

335435

Zoom out

Zoom in

1/13

Instructions for use, mounting and connection

Control elements

Once the glass ceramic hob is connected to the mains

(including the power failure), the appliance will perform the

process of initial synchronization with the exterior environment,

in order to provide the most efficient sensor function and

render the best control.

After the successful accommodation to the environment had

been completed, the indicators show the mark "-" for a

moment which eventually disappears.

The sound signal confirms the appliance is now ready for use.

Do not place any objects upon the sensor surface during the

accommodation period, otherwise you may provoke error

mode. In such cases the process is interrupted and all

indicators display the symbol ''F''. The hob fails to respond to

commands.

The hob is equipped with electronic sensors which are

switched on by touching or pressing the relevant sensor

surface with your fingertip.

Each sensor reaction is confirmed by the beep.

Be sure to always touch only one sensor at the time, and for a

very brief period of time (approximately 1 second). If more than

one sensor is pressed at the same time the relevant command

is not accepted. If the touch is prolonged it provokes error

mode and the appliance is switched off.

Do not place any objects upon the sensor surface (error mode)

nor any hot dishes which may damage the sensors. Keep the

sensor surface clean at all times.

Switching the hob on

When the hob is turned off all the hotplates are off and

indicator LED's are off.

To switch the hob on, touch the ON/OFF sensor. The hob is

activated and the hob #4 power display indicates flashing »0«

for a period of 10 seconds. Other hob indicators are not

illuminated. In case the main ON/OFF sensor was pressed for

more than 2 seconds, the hob is switched off and needs to be

restarted. Using the (+) or (-) sensor you may select the

desired cooking power in 10 seconds following the switch on or

selection of a particular hotplate.

Selecting the particular hotplate

Once the hob is switched on with the ON/OFF sensor, activate

the hotplate selection sensor to select the next hotplate in the

clockwise direction, always starting with hotplate #4. The

indicator flashes 10 seconds after the hotplate and its power

setting are selected. Active hotplate is indicated by flashing

power setting. By touching the (+) sensor you select setting "9"

and activate automated cooking mode. Current setting may be

reduced by touching the (-) sensor in short intervals. Prolonged

pressing speeds up the setting reduction. If you switch the

hotplate on by touching the (-) sensor, the power selection

indicates "4". This setting may then be increased or reduced by

pressing either (+) or (-) sensor and select the desired heating

power.

If the hotplate selection sensor is touched once again, you

select the next hotplate in clockwise direction, and this is

signaled by flashing of the indicator.

If only one hotplate is activated, by pressing the hotplate

selection sensor this hotplate is selected directly. In case more

than one hotplate is active, the first one to be activated is

always hotplate #4.

Switching the hotplate on

Once the hotplate is selected and its indicator flashes ''0'', you

have 10 seconds to select the desired power setting by

pressing either sensor (+) or (-). Indicator will flash the

selected setting, and after 10 second lapse this setting

becomes default.

If no power setting is selected within 10 seconds, the indicator

''0'' goes off and the hotplate is switched off.

Automatic cooking mode

When the automatic cooking mode is activated the hotplate will

operate at maximum power for a limited period of time

(depending upon the power level required for continuation) and

then automatically switch to the reduced power level to resume

cooking (see chart). It may be switched on in any of the

hotplates for all power settings except for maximum

setting 9.

Select the desired hotplate by touching the hotplate selection

sensor. Indicator ''0'' flashes.

Activate the automatic cooking mode by touching the (+)

sensor. In case setting "9" is not changed within the next ten

seconds the automatic cooking mode is off. It remains active if

you press the (-) sensor and reduce the power setting to any

value between 8 and 1. This means that the maximum setting

"9" must first be reduced by pressing the (-) sensor, and then it

may be increased by touching the (+) sensor. The indicator

displays letter ''A'' which remains illuminated for the entire time

the automatic cooking mode is on. Automatic cooking mode

will not function on power setting "9".

If you wish to check the power setting level of active hotplates

during automatic cooking mode, touch either (+) or (-) sensor.

The indicators of all active hotplates functioning in automatic

cooking mode will display the current power setting.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gorenje ect 600 e in the language / languages: English as an attachment in your email.

The manual is 1,24 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gorenje ect 600 e Manual

Product: