Manual Gorenje DKG552-ORA (page 13 of 88) (All languages)

603295

Zoom out

Zoom in

1/88

current category III, in accordance with installation

instructions.

Warning! Before re-connecting the hood circuit to the mains

supply and checking the efficient function, always check that

the mains cable is correctly assembled.

Mounting

Before beginning installation:

• Check that the product purchased is of a suitable size for

the chosen installation area.

• To facilitate installation, remove the fat filters and the

other parts allowed and described here, dismantle and

mount it.

To remove see also the relative paragraphs.

• Remove the active carbon (*) filter/s if supplied (see also

relative paragraph). This/these is/are to be mounted only

if you want lo use the hood in the filtering version.

• Check (for transport reasons) that there is no other

supplied material inside the hood (e.g. packets with

screws (*), guarantees (*), etc.), eventually removing

them and keeping them.

• If possible, disconnect and move freestanding or slide-in

range from cabinet opening to provide easier access to

rear wall/ceiling. Otherwise put a thick, protective

covering over countertop, cooktop or range to protect

from damage and debris. Select a flat surface for

assembling the unit. Cover that surface with a protective

covering and place all canopy hood parts and hardware

in it.

• In addition check whether near the installation area of the

hood (in the area accessible also with the hood mounted)

an electric socket is available and it is possible to

connect a fumes discharge device to the outside (only

suction version).

• Carry out all the masonry work necessary (e.g.

installation of an electric socket and/or a hole for the

passage of the discharge tube).

Expansion wall plugs are provided to secure the hood to most

types of walls/ceilings. However, a qualified technician must

verify suitability of the materials in accordance with the type of

wall/ceiling. The wall/ceiling must be strong enough to take

the weight of the hood. Do not tile, grout or silicone this

appliance to the wall. Surface mounting only.

Fig. 5-6

• Trace a central line on the wall in order to ease mounting

(1), position the hole template in a way that the middle

line printed on top corresponds to the central line marked

previously and the lower side of the mask corresponds to

the lower part of the hood once mounted. (2).

• Make 3 holes Ø 8 mm with a drill and fix the support

bracket with two dowels and screws to the wall (3), insert

the third dowel into the lower hole.

• Apply the support bracket „G“ to the adherent ceiling,

use the chimney support bracket as a hole scheme (if

present, the small eyelet found on the support should

coincide with the line previously traced on the wall) and

trace with a pencil 2 holes, drill the holes (Ø8mm), insert

2 plugs.

Fasten the support bracket to the wall with 2 5x45mm

screws (4).

• Open the vapour scheme and remove the grease filters

(see relevant paragraph).

• Hang the hood (5), regulate the position (6-7) and fasten

it securely with one screw and washer(8).

• Carry out electrical connections (9), but leave the hood

disconnected from the general electrical main panel.

• Install the flange supplied on the exit hole of the hood

(10).

• Carry out the connection of one tube (11 – tube and ties

for fastening not included, they need to be bought) for the

fume discharge to the connection ring placed on top of

the extractor motor unit.

The other end of the tube should be connected to a fume

expulsion device towards the outside, in case the hood is

used in extractor version.

In case you want to use the hood in filtering version,

fasten the deflector F to the support bracket, and connect

the other side of the tube to the connection ring placed

on the deflector (12).

Apply the chimneys and fasten them on with two screws

(13a) to the chimney support bracket „G“ (13b). and

make the lower part of the chimney slide into the suited

part on top of the chimney.

• Mount the grease filters and close the vapour scheme.

Warning! If the hood has to be used in extractor version,

remove, if supplied, the carbon filter and the fastening

wand (placed on the back of the grease filters – see

relative paragraph).

If the hood has to be used in filtering version, make sure

that the carbon filter is already mounted on the back of

the grease filter, or in case it’s missing, buy it and install

it.

Description of the hood

Fig. 1

1. Control panel

2. Grease filter

3. Grease filter release handle

4. Halogen lamp

5. Vapour catcher

6. Telescopic chimney

7. Air outlet (used for filter version only)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gorenje DKG552-ORA in the language / languages: All languages as an attachment in your email.

The manual is 2,07 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gorenje DKG552-ORA Manual

Product: