Manual Gorenje DK63CLI (page 3 of 80) (English, German, Dutch, French, All languages)

728672

Zoom out

Zoom in

1/80

ENGLISH

DESCRIPTION

The unit can be found in filtering hoods or in exhaust hoods. In the Filtering hoods (Fig. 1) the air and steam

taken up by the unit are purified with charcoal filters and returned to the environment through the aeration grids

on the side of the flue. WARNING: When using filtering hoods, both charcoal filters and an air deflector (A) must

be used. Located in the lower part of the flue, this deflector recycles the air to the environment. The charcoal

filters are not supplied. In the Exhaust hoods (Fig .2) an exhaust duct conveys the steam and cooking odors

directly outside through the wall/ceiling. Therefore they do not require charcoal filters.

Warning: Failure to install the screws or fixing device in accordance with these instructions may result in

electrical hazards.

INSTALLATION

To facilitate installation, before starting remove the grease filters: press inward on the clamp at the handle

and pull the filter downward (Fig. 3).

Mount the plate of the electrical system (depending on the model) fixing it with 2 screws and 2 metal washers

(Fig. 4).

Wall fitting (Fig. 5): making use of the appropriate drilling jig, apply the supplied blocks into the wall, and

remember the distance between the hood and the cooktop must be at least 65 cm. Insert two of the supplied

screws so that the apparatus can be hooked onto these ones by means of the holes provided on the appliance

(use the holes A; if the hood have the holes A and C, use only the holes C). Once the apparatus is hooked,

fix it definitively to the wall using the two other screws and the holes made at its bottom (B). To avoid damage

make exclusive use of the holes already prepared on the hood.

Securing the telescopic flue: Basic installation requirements: – Set the electrical power supply within the space

covered by the decorative flue. – If your unit is installed in an Exhaust hood, prepare the air exhaust hole.

Place bracket (W) 50 mm from the ceiling and position this on the vertical of your hood, with the aid of the notches

on the centre of the bracket (Fig. 6); using a pen, mark the 2 holes on the wall and then make the holes and

fit the screw anchors provided and proceed to secure the bracket using the 2 screws (provided).

Exhaust hoods: connect the disposal duct to the air evacuation pipe of the hood; use a flexible pipe and lock

it to the air evacuation pipe of the hood with a metal hose clamp (pipe and clamp are not provided). Make all

power connections to the hood by means of the power cable. Take 2 assembled flues and place these on the

upper surface of the hood. Raise the upper flue as far as the ceiling and secure it to the bracket using the 2

screws (Fig.7).

Filtering hood: make all power connections to the hood using the power cable. Fasten the air baffle to the lower

flue as shown in Figure 8, using the 2 screws. Take 2 assembled flues and place these on the upper surface

of the hood. Raise the upper flue as far as the ceiling and secure it to the bracket using the 2 screws (Fig.7).

Also remember that charcoal filters must be used in the case of the filtering version; check to see whether such

filters are already fitted; if necessary, proceed to fit as follows, depending on the model type purchased:

- if the hood features round charcoal filters (Fig. 9), fit the charcoal filter by turning anti-clockwise.

- if the hood features a panel type charcoal filter (Fig. 10), remove the two metal filter retainers (M) and position

the charcoal filter inside the grease filter; fit the two filter retainers back on again to secure the charcoal filter.

OPERATION

Depending on the model, the unit is equipped with the following controls:

Controls shown in Fig. 11: Button A: light switch. Button B: first speed motor ON/OFF switch. Button C: second

speed switch. Button D: third speed switch. E: motor on light. THE MOTOR FUNCTION WARNING LIGHT (E) IS

NOT PRESENT IN SOME MODELS.

Controls shown in Fig. 12: Button A: Light switch; position 0: light off; position 1: light on. Button B: Motor

switch; position 0: motor off; position 1-2-3: motor on at speed I, II and III. C: Motor pilot lamp.

Controls shown in Fig. 13: Button A: turns the LIGHTS off. Button B: turns the LIGHTS on. Button C: decreases

speed down to minimum speed. If pressed for 2" the motor is turned off. Button D: activates the motor (calling

the last speed used) and increases the speed until reaching maximum. Button E: FILTER ALARM/TIMER RESET:

when pressing the key during display of the filter alarm (motor off) it resets the hour counter. When pressing the

key when the motor is running, the TIMER is activated and the hood will automatically be switched off after 5

minutes.

L1) The 4 green LEDs indicate the running speed.

L2) When the LED is red (motor off) it indicates the FILTER ALARM. When the LED is green (flashing) it indicates that

the TIMER has been activated with the key E.

FILTER ALARM: After 30h of operation, the LED L2 turns RED. It indicates that the grease filters need to be cleaned.

After 120h of operation, the LED L2 turns RED and flashes; It indicates that the grease filters need to be cleaned and

the charcoal filters replaced. After cleaning the grease filters (and/or replacing the charcoal filters), restart the hour counter

(RESET) by pressing the key E during display of the filter alarm.

Controls shown in Fig. 14: Button A: turns the lights on/off; every 30 hours of operation the corresponding pilot

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Gorenje DK63CLI in the language / languages: English, German, Dutch, French, All languages as an attachment in your email.

The manual is 57,72 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Gorenje DK63CLI Manual

Product: