650414
32
Zoom out
Zoom in
Previous page
1/52
Next page
135
rogramación de los teléfonos T-740 Plus.
P
To show that the systemisreadyforprogramming,
the door panel and the telephone's handset will
reproduce a tone (the telephone led will light).
Audio communicationcanbeestablished.
Press the door panel push button that will call to
this telephone. At this moment both door
panel and handset will reproduce tones (the
telephone led will slow blink).
To programm the telephone as Master, press the
h (the telephone led will off).
Closethetelephone.
ook switch
Set to ON the switch number 2 of the SW2 configuration dip switch, placed at
the upper left side (back) of the sound module. The door panel will reproduce a
sound to advise that the system has entered into programming mode. In systems
with more than one door panel, the programming process shall be done on the
master door panel only.
Each apartment must have one master unit only; in case of parallel units configure them as slaves,
both monitors or telephones.
Make a call to check that the telephone has been succesfully programmed. Repeat
these steps to program the rest of telephones.
Once the programming has been finished, set to OFF the programming switch. If
you don't, the door panel will reproduce a tone to advise that the system is still
into programming mode.
To programm the telephone as Slave, press the
P1 door release push button (the telephone
led will quick blink) and later press the hook
switch (the led will off).
Closethetelephone.
Open the telephone to programming (see page
134). Select in the SW1 dip switch the fuction
mode for the auxiliary
(see page 133) and later press the P3
programming push-button.
function push button
To programm the telephone as Slave +
Intercom., press the P2 auxiliary function
push button (the led will quick blink) and later
press the hook switch (the led will off).
Closethetelephone.
To program the telephone from a general door panel (if it exists), see page 119.
TELEPHONES PROGRAMMING
P3
1 2
P3
ON
P3
ON
P3
ON
P3
ON
P3
SW1
1 2
P1
P2
CN1
M
S
SI
P1
P2
CN1
P3
SW1
P1
P2
CN1
ON
P3
ON
P3
SW1
P1
P2
CN1
ON
P3
SW1
P1
P2
CN1
ON
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Golmar T631 Plus Nexa at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Golmar T631 Plus Nexa in the language / languages: English as an attachment in your email.

The manual is 2,02 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info