467815
16
Zoom out
Zoom in
Previous page
1/18
Next page
2928
P operation mode.
I
IP mode allows to use this module in combination with "Stadio Plus"
panels, or to operate as stand alone module. The operation
mode selection is shown on page 27.
To enter into programming mode, a PIN code will be required.
This code of three digits length (override digit zero from left)
is sticked on the relay, placed on the left side of the display.
While programming, the led on the front part of the module
will light red. To exit from the programming mode, wait 20 sec.
from the last operation.
Press C button during 2 seconds.
The left digit display will show number 0.
To validate the code, press C button during 2 seconds:
the display will show the complete code.
In case of valid code, the display will show the
selected operation mode (IP). In case of wrong code,
the display will show the message "E–5" during
10 seconds and will automatically exit from the
programming mode.
Press arrow "DOWN" button to move to the next digit.
The left display will turn off and the center display
will show number 0.
Press arrow "DOWN" button to move to the next digit.
The center display will turn off and the right display
will show number 0.
Press arrow "UP" button till the first PIN digit will appears
on the display.
Press arrow "UP" button till the second PIN digit will
appears on the display.
Press arrow "UP" button till the last PIN digit will appears
on the display.
C
C
alidation of PROXCARD ISO cards
or NEOKEY key holders.
V
IMPORTANT: this module is to be used with ISO cards or key holders
supplied by Golmar. Other proximity items will be not accepted
even if they have the same appearance.
IMPORTANT:
IMPORTANT:
Once a valid PIN code has been introduced, the
display will show the 1st memory position.
Use "UP" and "DOWN" arrows to select the
desired position, from 1 to 500.
Several cards or key holders can be recorded in one
memory position. Remember that the maximum
number of cards or key holders (users) is 500.
When the display shows the desired memory position,
approach the card or key holder to be recorded.
The display will shows the number of cards
recorded in this position (including the one you are
recording). This number will be shown with a dot
on its right bottom part. The display will show the
selected memory position again.
If you are trying to record an already existing card,
the display will show the memory position where
recorded, coming back to the position you are
trying to record it.
Repeat the above steps to record the rest of cards.
To erase existing cards from a specified memory position,
use "UP" and "DOWN" arrows till the display shows
the desired position. Press C button during 3 seconds:
the display will show the number of cards recorded
in this position and will confirm the progress by
showing the message – – –.
To erase all the existing cards, press C button during
15 seconds aproximately: the display will show the
message "IP" once the memory is empty.
C
The module will exit from the programming mode afte 20 seconds of no operation.
The display and the led on the front part of the module will be turned off.
MODULE PROGRAMMING
MODULE PROGRAMMING
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Golmar T4502ML at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Golmar T4502ML in the language / languages: English, French as an attachment in your email.

The manual is 2,21 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info