642190
8
Zoom out
Zoom in
Previous page
1/24
Next page
eschrijving aansluitklemmen op de RC-Szena.
B
a. Monitor-inhanghaken (x2).
b. Bevestigingsgaten ten behoeve van opbouw bevestiging op een vlakke muur.
c. Label met informatie over de aansluitklemmen.
d. Clip om monitor in de ophanging te vergrendelen en te ontgrendelen.
e. Identificatie label.
f. Kabelinvoer gat.
g. Aansluitklemmen:
1. Aansluiting voor draad 1 BUS uit.
2. Aansluiting voor draad 2 BUS uit.
3. Aansluiting voor draad 1 BUS in.
4. Aansluiting voor draad 2 BUS in.
5. Aansluiting voor etage beldrukker HZ IN.
6. Aansluiting voor etage beldrukker HZ IN.
7. Aansluiting voor doorlus naar Slave monitor “etage beldrukker” HZ UIT.
8. Aansluiting voor doorlus naar Slave monitor “etage beldrukker” HZ UIT.
9. Potentiaal vrij contact PA (I. Max: 40mA).
10. Potentiaal vrij contact PB (I. Max: 40mA).
11. Aansluiting voor externe deuropener knop bijv. voor tandarts.
12. Aansluiting voor externe deuropener knop bijv. voor tandarts.
13. Aansluiting voor externe signaalgever (-) (S-45).
14. Aansluiting voor externe signaalgever (+) (S-45).
b
f
g
b
d
b
e
b
a
c
*
( )
Belangrijk: Als de monitor niet op de aansluitstrip is geplaatst zullen monitoren of telefoons in
serie niet functioneren indien aangesloten via BUS IN en BUS UIT.
7
BESCHRIJVING MONTAGEPLAAT
8
PLUS V2PLUS
+
-
Vin / Mp
Malla
Vout / Vp
Audio
Data
HZ-
-
SA
+
Int
PB
PA S+
S-
AP
AP
PB
PA
HZ out
HZ in
BUS in
BUS out
11
2
3
4
5
66
7
8
9
10
11
12
13
14
*
( )
BESCHRIJVING VAN DE MONITOR
indweerstand/signaalversterking video.
E
DIP-schakelaar Sw1 bevindt zich aan de linkerzijde van de achterkant
van de monitor. 4-voudig DIP-schakelaar.
Eindweerstand 107Ω, standaard op UIT laten.
Eindweerstand 165Ω, standaard op uit laten.
Fabrieksinstelling
Video Boost: Zet deze op AAN indien de monitor 65m of meer van een
multiplexer verwijdert is of achter de uitgang van de ± 20ste verdeler.
Indien de monitoren in serie zijn geplaatst zet deze dan op AAN achter de
9de monitor of na ± 80 meter.
Laat deze op UIT bij monitoren voor de overige monitoren.
Eindweerstand 130Ω (End of line), zet deze op AAN indien dit de laatste
monitor betreft. Laat deze UIT voor alle tussenliggende monitoren. Indien
het beeld te licht is kan eventueel schakelaar 1 en/of 2 ook op AAN gezet
worden. Weerstanden worden parallel geschakeld.
1 2 3 4
ON
SW1
eschrijving van DIP-schakelaar Sw2. 10-voudige DIP-
Bschakelaar.
De programmering van een monitor kan gedaan worden middels het installateurs
menu (zie pagina 15-16) of door DIP-schakelaar Sw2 in te stellen (zie pagina 14).
Dip1 en Dip2: Instellen monitor Master/ Slave.
Fabrieksinstelling
Dip3 tot Dip10: Instellen van de monitor-code.
1 2 3 4
5 6 7 8 9 1
0
ON
SW2
Belangrijk: Om te programmeren via DIP-schakelaar SW2 (zie pagina ).14
.
Let op: Deze manier van programmeren schakelt het programmeren via het installateurs menu
uit (zie pagina 15-16).
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Golmar SZENA V2PLUS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Golmar SZENA V2PLUS in the language / languages: Dutch as an attachment in your email.

The manual is 5,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info