467816
8
Zoom out
Zoom in
Previous page
1/56
Next page
110
DOOR PANEL INSTALLATION
ssembly the sound module.
A
Insert the sound module in the grille module.
For a proper assembly, align the light
push button and the microphone rubber
of the sound module with its corresponding
holes in the grille module.
Link the sound module with the keypad module
by using the supplied flat cable.
Select a direction to open the door panel; this selection should ease
the door panel wiring.
The opening direction will be settled through the hinges position,
that must be passed through the header clips as shown.
For example, if the hinges are placed on both clips of the lower
header, the door panel will open downwards; if they are placed
on the right clips of both headers, the door panel will open to left.
To hold the door panel on the embedding box,
insert the hinges in the embedding box lockers
as shown.
old the door panel on the embedding box.
H
111
DOOR PANEL INSTALLATION
Enabled.
Disabled.
Coaxial. Twisted pair.
Maximum. Minimum.
Reset. Standby.
Jumper JP1 loads the installation with a communications
resistor. For a proper system operation, activate this resistor
only in the closest door panel to the backbone installation
or in the general entrance door panel (if exists).
Factory default: enabled.
Jumper JP2 selects the type of cable to be used for the video
signal: coaxial cable (RG-59 or RG-11) or twisted pair.
Twisted pair video transmission requires the use of an
EL560 module plugged in the CN4 connector.
Factory default: coaxial cable.
Jumper JP3 selects the volume of the door panel acknowledgement
signals (call in progress, system busy and door opened).
If after starting the system it's considered that the volume is too
high, modify the jumper position.
Factory default: maximum.
Jumper JP4 allows to reset the installer PIN code to the factory
default (see page 114).
Use this function only in case to forget this code.
With the system switched on, change the jumper position
to reset the code and return it to the standby position.
escription of the configuration jumpers.
D
The JP1, JP2, JP3 and JP4 configuration jumpers
are placed on the left side of the terminal connector.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Golmar 5403 Stadio Plus - T3403ML at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Golmar 5403 Stadio Plus - T3403ML in the language / languages: English as an attachment in your email.

The manual is 7,94 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Golmar 5403 Stadio Plus - T3403ML

Golmar 5403 Stadio Plus - T3403ML User Manual - English - 160 pages

Golmar 5403 Stadio Plus - T3403ML User Manual - Dutch - 24 pages

Golmar 5403 Stadio Plus - T3403ML Installation Guide - Dutch - 52 pages

Golmar 5403 Stadio Plus - T3403ML User Manual - French, Spanish - 160 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info