505299
4
Zoom out
Zoom in
Previous page
1/24
Next page
i
SAFETY PRECAUTION
CAUTION:
The lightning flash with
arrowhead symbol, within
an equilateral triangle, is
intended to alert the user
to "dangerous voltage"
and to prevent from a risk
of electric shock.
Warning:
To reduce the risk of
electric shock, don't open
the cabinet. Refer
servicing to qualified
personnel only.
The exclamation point
within an equilateral
triangle is intended to alert
the user to important
operating and
maintenance (servicing).
WARNING: Do not use this STB where contact with or immersion in water is a possibility. Do
not use near flower vase, washbowls, kitchen sinks, laundry tubs, swimming pools, etc.
WARNING: Do not put the candle or lamp stand on the cabinet; otherwise, there is the danger
of fire.
WARNING: The unit should be connected to a power supply only of the type described in the
operating instructions or as marked on the unit. If you are not sure of the type of power supply
(for example, 120 or
230 V) to your home, consult your local dealer or local power company.
WARNING: This product install diodes. Do not open the cabinet or touch any parts in the inner
mechanism. Consult your local dealer for technical service if the opening is required.
Note: To ensure proper use of this product, please read this User manual carefully and
retain for further reference.
Note: This product install diodes. Do not open the cabinet to avoid the unit direct exposure to
radiation.
Unit Cleaning: After the unit power is turned off, you can clean the cabinet, panel and remote
control with a soft cloth lightly moistened with a mild detergent solution.
Attachments: Never add any attachments and/or equipment without the manufacturer
consent; as such additions may result in the risk of fire, electric shock, or other personal injury.
Locating: Slots and openings in the cabinet are provided for ventilation to protect it from
overheating. Do not block these openings or allow them to be blocked by placing the STB on a
bed, sofa, or other similar surface, nor should it be placed over a radiator or heat register.
Power-Cord Protection: Place the power-supply cord out of the way, where it will not be
walked on. Please take special attentions to cords at plugs, convenience receptacles, and the
point where they exit from the unit.
ii
Object and Liquid Entry: Never put objects of any kind into this STB through openings, as
they may touch dangerous voltage points or short-out parts that could result in a fire or electric
shock. Never spill any liquid on the STB.
Note: Moisture may be formed on the lens In the following conditions:
when the unit is suddenly moved from a cold environment or an air-condition room to a
warm place.
immediately after a heater has been turned on.
in a steamy or very humid room.
If the moisture forms inside the unit, it may not operate properly. To correct this problem, turn
on the power and wait about two hours for the moisture to evaporate.
Parts Replacement: When the unit parts need to be replaced, user should make sure the
service technician use the replacement parts specified by the manufacturer or having the
same characteristics as the original part. Unauthorized replacement may put the unit In the
risk of fire, electric shock or other hazards.
Safety Check: After all the maintenances and repairs are done, user is required to request the
service technician to conduct the overall safety check to ensure the machine is In the proper
condition.
Basic Operations
3
CONTENTS
1.
REMOTE CONTROL.......................................................................................................4
2.
FRONT PANEL ...............................................................................................................5
3.
REAR PANEL .................................................................................................................5
4.
CONNECTING YOUR SYSTEM......................................................................................6
5.
CHANNEL.......................................................................................................................7
5.1
TV
C
HANNEL
M
ANAGER
............................................................................................................... 7
5.1.1
Group .........................................................................................................................................................................7
5.1.2
Skip.............................................................................................................................................................................8
5.1.3
Edit.............................................................................................................................................................................8
5.1.4
Sort.............................................................................................................................................................................9
5.1.5
Favorite......................................................................................................................................................................9
5.1.6
Find ..........................................................................................................................................................................10
5.2
R
ADIO
C
HANNEL
L
IST
.................................................................................................................. 10
5.3
D
ELETE
A
LL
................................................................................................................................. 10
6.
INSTALLATION ............................................................................................................11
6.1
I
NSTALLATION
............................................................................................................................. 11
6.2
CA
S
ETTING
................................................................................................................................. 13
7.
SYSTEM SETUP...........................................................................................................13
7.1
L
ANGUAGE
................................................................................................................................... 14
7.2
TV
S
YSTEM
.................................................................................................................................. 14
7.3
L
OCAL
T
IME
S
ETTING
.................................................................................................................. 15
7.4
T
IMER
........................................................................................................................................... 15
7.5
S
TARTUP
C
HANNEL
...................................................................................................................... 16
7.6
C
HANNEL
P
LAY TYPE
................................................................................................................... 17
7.7
OSD
S
ETTING
............................................................................................................................... 17
7.8
P
ARENTAL
L
OCK
.......................................................................................................................... 18
8.
TOOLS ..........................................................................................................................19
8.1
I
NFORMATION
.............................................................................................................................. 19
8.2
S
ATELLITE
G
UIDE
........................................................................................................................ 19
8.3
D
EFAULT
V
ALUE
.......................................................................................................................... 20
8.4
S
OFTWARE
U
PGRADE
................................................................................................................... 20
9.
GAME............................................................................................................................22
9.1
T
ETRIS
.......................................................................................................................................... 22
9.2
S
NAKE
.......................................................................................................................................... 22
9.3
O
THELLO
...................................................................................................................................... 22
10.
TROUBLE SHOOTING .................................................................................................23
11.
SPECIFICATIONS.........................................................................................................24
11.1
G
ENERAL
...................................................................................................................................... 24
11.2
A/V
M
ODE
................................................................................................................................... 24
11.3
M
ICROPROCESSOR
&
M
EMORIES
................................................................................................. 24
11.4
P
OWER
&
E
NVIRONMENT
C
ONDITION
......................................................................................... 24
11.5
P
HYSICAL
S
PECIFICATION
............................................................................................................ 24
11.6
C
ONNECTION
................................................................................................................................ 24
Basic Operations
4
1. Remote Control
You can power on/off the receiver, operate on screen menu, and use a variety of hot key function.
POWER
To switch your receiver on from standby or standby to on.
MUTE
Used to enable or disable the audio
MENU
Displays the Main Menu on the screen, or return to the previous menu
or status
(PREVIOUS
)
Return to the previous menu or status.
SAT
Display satellite list.
EXIT
Cancel the user selection and return to the viewing mode from a menu.
(
((
(
TV / RADIO)
Receiver switches between TV and Radio mode.
(INFORMATION)
To display channel status or various program information of current
service.
NUMERIC KEYS
Used to select channels or enter programming parameters
OK
To select menu option, or to updated on entry.
PAUSE
Used to select the freeze function.
Press once to freeze the screen picture.
Press again to go to normal state.
<,> KEY
To adjust volume level, or to move cursor left or right in the menu
^,v KEY
To change channels, or to move cursor up or down in the menu
UHF
In case your TV is connected through RF Modulator (UHF), select
output channel number between CH21 and CH69 with up and down
key.
FAV(FAVORITE)
To set receiver to the favorite server mode,
display the favorite channel
AUDIO
To select audio mode; Left, Right, Stereo
P+/P-
To move up the cursor to the next or previous page
in the menu or channel list
TV/SAT
Receiver switches between TV and Satellite receive mode.
(ZOOM)
Press key select zoom times, from X1 to X16.
(WHITE KEY)
Subtitle Display.
TIMER(YELLOW KEY)
Press timer key then enter timer menu. You can setup up total 8 tasks.
(RED KEY)
Audio channels setup, to select audio mode; Left, Right , Stereo.
(GREEN KEY)
Multi channels display. You can choice the desire channel use <,> ^,v
and press ok confirm.
TELETEXT(BLUE KEY)
Shows teletext information of the current channel supports.
(FIND)
Use to prompt find channels sort by character.
Basic Operations
5
2. Front panel
POWER: To switch the receiver power on/stand by
VOL^, v KEY: To adjust volume level, or to move cursor left or right in the menu
CH ^, v KEY : To change channels, or to move cursor up or down in the menu
Remote Sensor: Detects infrared signal from remote control unit
Display(4-Digit/7-Segment): Indicates operating status of receiver
Power Led: Lights up while the receiver is power on
Signal Led: When receiving signal is strong, the signal led is lighted.
MENU KEY: To enter into the main menu
OK KEY: To see TV/Radio channel list, or to confirm in the menu
3. Rear Panel
Please refer to the diagram above for all possible connections of your receiver
Do not connect the unit to the mains socket until all other connections have been made and
checked.
LOOP: This enables the connection of another receiver.
13/18V 500mA MAX LNB IN: This port is to connect the coaxial cable from LNB of your Dish.
ANT IN: Connect to Analog TV antenna.
TV OUT : This is used to connect your TV through RF cable.
VIDEO : This RCA connector is used to connect any external video.
0-12V :This is used to Connect 12V to an external 0V/12V switch.
AUDIO R/L : These RCA connectors are used to connect any external audio amp or system.
RS 232C SERIAL PORT: This is used to connect your receiver to a computer through a serial
cable.
TV : This is used to connect your TV through SCART cable.
Basic Operations
6
4. Connecting Your System
There are three ways to connect the receiver to your existing TV system. We recommend using one
of the following cases for the best result :
1. Connect one end of SCART cable to the TV(SCART) jack on the back of the receiver and the
other end to a SCART jack on your TV.
2. Connect one end of RCA cable to the RCA jack on the back of the receiver and the other end to a
RCA jack on your TV.
3. If your TV doesn't have a RCA jack, connect one end of RF cable to the TV on the back of the
receiver and the other end to a RF input jack on your TV.
Finally connect the coaxial cable from the LNB to the LNB IN jack on the receiver.
_ With External Audio / Hi-Fi System
To connect any external Audio Hi-Fi system, the receiver has been provided with two RCA
connectors
at the back of the receiver marked with Audio L and R.
Connect an RCA stereo cable from the AUDIO L, R jacks on the back of the receiver to the LINE,
AUX, SPARE OR EXTRA input jacks on your Hi-Fi System.
4.1 TV with Motorized System (DiSEqC 1.2)
Connect one end of your coaxial cable to the LNB IN connector on the receiver and the other end to
the REC or Receiver connector on the DiSEqC 1.2 motor.
Connect the coaxial cable from the LNB to the LNB connector on the DiSEqC 1.2 motor.
All our receivers are designed to be DiSEqC 1.0 and DiSEqC 1.2 compatible.
This allows multiple antennas to be connected to the receiver at the same time.
If you have two or more fixed antennas or LNBs, then we recommend you use a DiSEqC 1.0
switch.
Connect the coaxial cable from the first LNB to the LNB 1 or LNB A input connector of the DiSEqC
switch.
Do the same for any other LNBs that you have.
Connect one end of a coaxial cable to the RF output connector of the DiSEqC switch,
connect the other end to the LNB IN socket on the receiver.
To the digital receiver, you can connect either a single satellite antenna directly or LNB of
multi-feed equipment.
Menu Operations
7
5. Channel
When you press[Menu]key to enter menu,
there will display the picture like below:
1
Press[Up/Down]key to select menu pages
among Channel, Installation, System and
Tools.
2
Press[OK]key to enter the selected item.
In “Channel” menu:
1
Press[Channel Up/Channel Down]key to
select menu items among TV Channel, Radio
Channel and Delete All.
2
Press[OK]key to enter the selected item.
5.1 TV Channel Manager
When you enter to “Channel List” menu, there
will display the screen like below.
1
You can move highlight by press[Channel
Up/Channel Down]key and press[OK]key to
preview the current highlighted program in the
right side preview window.
2
You can press[Page Up/Page Down]key to
implement the Page Up/Page Down function.
3
You can use Red button to switch “Program
Group”.
4
You can press[Menu]or[Exit]keys to enter full
screen playing mode.
5
Press color key can implement the
corresponding function in “Channel Manager”.
5.1.1 Group
1
Press [Red] key can open the “Group” window
like above
2
You can press [Up/Dwon] key to move
highlight and press [OK] key to select group.
3
Press [Red] key or [Menu] key to close
“Group” list.
Menu Operations
8
5.1.2 Skip
1
In “TV Channel Manager” menu, press
[Green] key can make a “skip mark” in the
right side of the highlighted channel.
2
After save and exit “TV Channel Manager”
menu, the channel will be skip while user
change channel in the full screen.
5.1.3 Edit
Press [Yellow] key, it will show input password
dialog. If the password is correct, it will open the
window like below. The default password is
0000.
5.1.3.1 Delete
1
In this menu, press [Red] key can make a
delete mark in the right side of the highlighted
channel.
2
Press [Red] key again can cancel the deleted
mark on the current channel.
3
When exit the menu, it will ask you whether to
save the change. Select “Yes” to save the
change.
5.1.3.2 Create
If you press[Green] key, it will display create
window like below:
1
In “Satellite” item, press[OK] key can
display satellite list and you can select a
satellite that you want to setting.
2
In “TP Index” item, you can press[Volume
Up/Volume Down]key can switch TP
number, and the next three items will show
up corresponding parameters.
3
In “Name” item, press[OK]key can display
the keypad, and you can edit new name
here for selected channel.
4
In “Video PID”, “Audio PID” and “PCR PID”
items, you can use the number key directly
to modify corresponding parameters of the
items.
5
After modification, move highlight to “Save”
item and press[OK]key, can save
parameter and exit “Edit” mode. Otherwise,
move highlight to [Exit]item and
press[OK]key can exit “Edit” mode and
won’t save any modification.
5.1.3.3 Edit
If you press[Yellow] key, it will show the window
like below:
Menu Operations
9
1 On the “Name” item, press[OK]key can
display keypad to edit the name of selected
channel.
2 On the “Video PID”, “Audio PID” and “PCR
PID” items, you can input numerals to
modify the according item’s value.
3 After modification, move highlight to “Save”
item and press[OK]key can save the
modified value and exit “Edit” mode.
Otherwise, move highlight to [Exit]item and
press[OK]key can exit “Edit” mode and
won’t save any modification.
5.1.3.4 Lock
Press [Blue] key can make a “lock mark” in
the right side of the highlighted channel.
After save and exit the menu, STB will
request you to input the password while you
want to watch the locked channel.
5.1.3.5 Move
1
In this menu, press [White] key can make a
moving mark in the right side of the
highlighted channel.
2
Press [Up/Down] key to move the channel
3
Press [OK] key to put the channel to the
target place.
4
When exit the menu, it will ask you whether
to save the change. Select “Yes” to save
the change.
5.1.4 Sort
1
Press [Blue] key can open the “Sort”
window like above. There are five kinds of
sorting ways. You can press[Channel
Up/Channel Down]key to move highlight
and press[OK]key to confirm you selection
2
The five kinds of sorting way are:
Default: Sorting by scanning result.
Name (A-Z): Sorting in Alphabetical
Order, ignore “$” symbol.
Name (Z-A): Sorting in Alphabetical
Order, ignore “$” symbol.
FTA: Sort channel by free and scramble
sequence. Free channel will at front of
channel list and scramble channel will at
reat of channel list
Lock: Accumulated all locked channels
and list in the last of TV Channel List.
5.1.5 Favorite
Menu Operations
10
1 Press [White]key can open the “Favorite”
window like above
2 You can move highlight between 8 favorite
groups by press[Channel Up/Channel
Down]key and press[OK]key to make a
favorite mark in the right side of the
selected Favorite group.
3 Press[OK]key on the marked Favorite
group can cancel the exist favorite mark.
4 After marking, press[Exit]key can back to
“TV Channel List” , there will show a
favorite mark beside the marked channel.
5.1.6 Find
1
Press[Find] key can open the “Find”
window like above. You can press[Channel
Up/Channel Down/Volume Up/Volume
Down]key to move highlight and
press[OK]key to input the selected symbol
or letter into the dialogue.
2
After input each character, the program list
on the left will search the channel
according your input, and list the matched
channel.
3
Press[Exit]key can close “Find” window
and you can select channel from the
channels list directly.
5.2 Radio Channel List
Basically, the operation of “Radio Channel
Manager” is same as “TV Channel Manager”,
but there is one point different: In “Radio
Channel Manager” mode, there is no video
information, so it will always display Radio’s
logo in the right side preview window.
5.3 Delete All
In “Delete All” item:
1
There will display an dialogue for user to
key in password. The default Password is
“0000”.
2
When you input the correct password, there
will show up a warning message box to
inquire you whether delete all or not.
3
If you select “Yes”, all channels will be
deleted.
4
In step 1 and step 2, press[Exit]key can exit
the function directly without save.
? Frequently Asked Question
Q: IF I incautiously delete all channels,
what should I do?
A: there are two ways to restore:
To re-search all channels in “Installation”
function.
Use “Default Value” function to restore all
channels in “Tools” function.
Menu Operations
11
6. Installation
6.1 Installation
When you enter to “Installation” menu, there will
display the screen like below:
6.1.1 Satellite
1
Satellite: Press[OK]key to enter the Satellite
list.
2 You can press color key to add/edit/delete satellite.
Press [Page] key to page up or page down.
6.1.2 DiSEqC
DiSEqC: You can use[Volume Up/ Volume
Down]key to switch options. There are several
options for your selection:
Disable: without DiSEqC.
1/2, 2/2: two ports DiSEqC
1/4, 2/4, 3/4, 4/4: 4 ports DiSEqC
1/8, 2/8… 8/8: 8 ports DiSEqC
1/16, 2/16….16/16: 16 ports DiSEqC
6.1.3 Positioner
Positioner: In “Positioner” item, you can press
[Volume Up/ Volume Down]key to switch “None /
DiSEqC 1.2 / USALS” functions.
6.1.4 LNB Type
In this item, press[Volume Up/ Volume
Down]key can switch among “Standard”, “User”
and “Universal” mode.
6.1.5 22K
You can use[Volume Up/ Volume Down]key to
switch “ON / Off”. When this item is switched to
“ON”, receiver will receive TV and radio input
Menu Operations
12
signal from 22K port. If the item is switched to
“Off”, the receiver will receive all signal from 0K
port.
! Notice
When you choose LNB type “Universal”, you can
not modify 22K.
6.1.6 0/12V
You can use[Volume Up/ Volume Down]key to
switch “0V / 12V”. When this item switches to
“12V”, receiver will receive TV and radio input
signal from 12V port. If the item switches to
“0V”, the receiver will receive all signals from 0V
port.
6.1.7 Tonebusrt
In “Toneburst” item, you can press [Volume Up/
Volume Down]key to switch “Off/On” functions.
6.1.8 Polarity
In “Polarity” item, [Volume Up/ Volume
Down]key to switch “Auto / H / V” functions.
6.1.9 TP Edit
When you enter to “TP Edit” menu, there will
display the screen like below:
1
In “Satellite” item, press[Volume Up/ Volume
Down]key to switch satellite that you want to
scan or press[OK]key to enter satellite list for
selection.
2
In “TP Index” item, you not only can use
[Volume Up/ Volume Down]key to select
transponder but also can
use[Add]and[Delete]functions.
When you press[Green] key, it will display
“New TP” in “TP Index” item; You should
set the parameters of “TP Frequency” and
“Symbol Rate” for this new transponder.
The parameters of “TP Frequency” and
“Symbol Rate” can set by number keys.
The available range are “3000~13450
MHz” and “1000~45000Ks/s”.
When you press[Yellow] key, there will
show up a warning message for reminding
whether you will delete the current
transponder or not. If you select “Yes”, the
current transponder will be deleted, and
the total account of transponder will reduce
1 correspondingly.
When you press [Blue] key, there will show
up a warning message for reminding
whether you will delete all transponders or
not. If you select “OK”, all transponders will
be deleted.
3
For the existed transponder, you also can
use number keys to modify the parameters
of “TP Frequency” and “Symbol Rate”.
4
When you complete your modification,
Press [Red] key, it will show up a dialog to
ask you scan mode, program type, scan
type and NIT Search on/off. After you set
up, press [OK] key to start scanning.
5
In the “TP Scan” item, press [Exit] key to
exit the scanning and save the current
parameters.
6.1.10 Single Scan
1
Press [Red] key, it will show up a dialog to
ask you scan mode (means you want to
scan all channels or only scan free
channels), program type (means you want
to sean all channels or only sean TV/Radio
Menu Operations
13
channels), scan type (means preset scan,
that is searching the existed TP. Automatic
Scan means blind scan. It is no need
existed TP info) and NIT Search on/off.
After you set up, press [OK] key to start
scanning.
6.1.11 Multi Search
1
Multi Search can support search the multi
satellite one by one as user select.
2
Press [Red] key, it will show up a dialog to
ask you scan, program type, scan type and
NIT Search on/off. After you set up, press
[OK] key to start scanning.
6.2 CA Setting
We provide one CA slots for user to use.
Receiver has build in smart card module with
CONAX system. By using cards in this system
provided by operators, it is possible to watch
many scrambled channels coded in this system.
This menu shows detailed information about
cord inserted into cord reader module. It allows
inserted according to help messages visible on
the bottom of the screen.
Note:
All information showed in this menu and
submenu are coming from inserted card. In
case if anything is wrong, it could be card
problem. After inserting the card correctly at any
time, a message-box will show on the screen
with message about detecting the card, in "card
info" menu all available information will be
displayed.
7. System Setup
When you enter to “System Setup” menu, you
will see the screen like below:
In “System Setup” menu:
1
Press[Channel Up/Channel Down]key to
select menu items among Language, TV
System, Time, Timer, Channel Play Type,
Startup Channel OSD Setting, Parental
Lock.
2
Press[OK]key to enter the selected item.
Menu Operations
14
7.1 Language
When you enter to “Language” menu, you will
see the screen like below:
1
Language: press[Volume Up/ Volume
Down]key to select languages, the
selections of languages include: English,
French, German, Portuguese, Turkish,
Spanish, Polish and Italian.
2
First Audio: Some channels have more than
one audio language for choosing; by this
function you can set the first audio for this
channel. If the playing channel has the same
audio as the “First Audio” you set, system will
play this audio language as default. If the
channel hasn’t the suited audio language,
then the system will compare automatically
with second audio language. The selections
of audio languages include: English, French,
German, Russian, Arabic, Portuguese,
Turkish, Spanish, Polish and Italian.
3
Second Audio: If the channel has no
correspond audio with “First Audio” but have
corresponded audio with “Second Audio”,
system will play the second audio language
as default. If no audio language corresponds
with the “Second Audio”, then the default
language of current channel will be played
automatically. The selections of audio
languages include: English, French, German,
Russian, Arabic, Portuguese, Turkish,
Spanish, Polish and Italian.
4
EPG: Press [Left/Right] key can select EPG
language.
5
Subtitle Language: Press [Left/Right] key can
select subtitle language.
6
Press[Exit]key to draw back from “Language”
menu.
7.2 TV System
When you enter to “TV System” menu, you will
see the screen like below:
1
Display Mode is use for switching the
screen-displaying mode. Now we provide
below options: Auto / PAL-M / PAL-BG /
NTSC. You can press[Volume Up/ Volume
Down]key to select each mode circularly.
2
Aspect Mode is used for switching the
screen aspect ratio mode. Now we provide
below options: 4:3 PS / 4:3 LB / 16:9. You
can press[Volume Up/ Volume Down]key to
select each mode circularly.
3
Video Output: Press [Left/Right] to select
CVBS or RGB.
4
RF System is use for switching RF format.
Now we provide below options: PAL-BG /
PAL-I / PAL-DK / NTSC.
Menu Operations
15
5
RF Channel is use for setting TV frequency
range, please refer to the table as below:
System Range
PAL-BG 21~69(Italian; default
value)
28~68(Australian)
PAL-I 21~69
PAL-D/K 13~57
NTSC 14~69
RF function can receive satellite TV channel
from receiver and add new channel to your
TV channel. After setting, while you want to
see the satellite channels, you can search
the channel in TV mode and needn’t switch
video to AV mode.
6
Press [Exit]key to draw back from “TV
System” menu.
7.3 Local Time Setting
When you enter to “Time & Timer Setting”
menu, you will see “Time” and “Timer” items.
1
Time: When you select “Time” and
press[OK]key to enter the menu, you will see
the screen like below:
GMT Usage: This item is use for open the
usage of GMT. You can press[Volume Up /
Volume Down]keys to switch “On/Off”.
The “GMT Offset” item is valid only when
the setting of “GMT Usage” is “Yes”. You
can press[Volume Up / Volume Down]keys
to switch “GMT Offset” value, and the
range is “-12:00 ~ +12:00”, increase each
half hour progressively.
You can press [Left/Right] to control
Summer time on or off.
Date” and “Time” items are valid only when
the setting of “GMT Usage” is “No”. You can
press [Volume Up / Volume Down]keys to
moving highlight and use number keys to
input directly.
If the current channel provides the correct
time information, you will see the current
time while you enter “Time” menu. If the
channel doesn’t provide time information,
you have to input the date and time
information manually.
Time Display can control time display on or
off when full screen play.
Press[Exit]key to draw back from “Time”
menu.
7.4 Timer
press [enter] key to open timer menu.
Current time information will display on the
first column; if the current time is incorrect,
please modify the time information in “Time
item.
Timer Number: You can press[Volume Up /
Volume Down]keys to set Timer number, and
there are 8 timers in total.
Timer Mode: There are several modes for
Timer to setting, include Off, Once, Daily,
Weekly, Monthly and Yearly.
Timer Service: There are two options for
“Timer Service”, include “TV Channel” and
“Radio Channel” (timer setting for channel
change and Wakeup/Sleep) and Message
(reminding message).
Menu Operations
16
When you select “Channel” (timer setting for
channel change and Wakeup/Sleep) option
in “Timer Service”, the screen will display like
below:
Wakeup Channel: press[OK]key to
enter channel list and select channel
that you want to setting.
Wakeup Date: use number keys to input
your wakeup date.
On Time: use number keys to input your
wakeup time. Once the time’s up, no
matter what the system is in standby
mode or in playing mode, the system will
automatically switch to the channel you
want and start to play.
Duration: After you set a time for
“Duration” item, once the time’s up, the
system will automatically switch to
standby mode. If you want not work this
function, set the duration is 00:00.
When you select “Message” (reminding
message) option in “Timer Service”, the
screen will display like below:
Wakeup Message: press[Volume Up /
Volume Down]key to select reminding
message as Birthday, Anniversary and
General.
Wakeup Date, you can use number
key to input your wakeup date.
On Time: use number keys to input
your wakeup time. Once the time’s up,
no matter what the system is in
standby mode or in playing mode, the
system will automatically pop a
reminding message.
The message will always display on
the screen, you can press[Exit]key to
close it.
Press[Exit]key to exit the current menu.
7.5 Startup Channel
Press [OK] key to enter “Startup Channel”
menu, and you will see the screen like below:
Menu Operations
17
If the setting of “Boot on Channel” is
“On”, it means the following two items
can be work. If the setting is “Off”, it
means the “Boot on Channel” function
can’t work.
In the “Mode” item, you can set the
“Startup Channel” as “TV channel”
mode or “Radio channel” mode.
In “Startup Channel” menu, you can
press[OK]key to open the channel list,
and select the channel that you want it
to startup, press[OK]key again to
confirm.
7.6 Channel Play type
1
Press[OK] key to enter “Channel Play Type”
menu, and you can select the “playing
channels” as “Free”, “Scrambled” or “All”.
2
For Example: If you select “Free”, in full
screen play, all scrambled channels will be
skipped when you change channels by
use[Channel up/Channel Down]key.
3
Press[Exit]to draw back from “Channel
Setup” menu.
7.7 OSD Setting
When you input to “OSD Setting” menu, you will
see a screen like below:
1
Subtitle Display: You can press[Volume
Up/Volume Down]key to select “On” or
“Off”. If the current channel has subtitle
information, it will be showed up while this
function is “On”. If this function is “Off”,
there won’t show up subtitle information
even if the current channel has subtitle
information.
2
OSD Timeout: When you switch channels
in full screen, there will show up some
information about current channel on the
lower of the screen. And regarding to the
duration of these information show up on
the screen, you can press[Volume
Up/Volume Down]key to set the time. The
range of the duration is “1 second ~
10seconds”.
3
OSD Position: control display position of
the info bar in full screen mode. You can
choose “bottom” or “top”.
4
OSD Transparency: Besides the setting of
“OSD Menu Style”, you also can set the
transparency of OSD. You can
press[Volume Up/Volume Down] key to
select the values. There are 5 levels of
transparency, 10%, 20%, 30%, and 40%
and “NO” (means no transparency
function).
5
Load OSD Setting Default: If you are not
satisfy with your setting, you can move
Menu Operations
18
highlight to this item and press[OK]key to
reset parameters as default value.
6
Press[Exit]key to draw back from the “OSD
Setting” menu.
7.8 Parental Lock
You can set a password for anyone who wishes
to operate in the “Installation” menu. And you
can also set the password for the lock channels.
(How to set the lock channel please refer to
LOCK) Here will show you how to setting and
how to revising the password.
1
In “Parental Lock” function, press[OK]key,
there will pop an dialogue for you to input
the password. When you input the correct
password, you will see a screen like below:
2
Menu Lock determining that when user
wish to enter “Installation” menu, whether
have to input Password or not. If the
setting of “Menu Lock” is “Yes” which
means user have to key in password, set
“No” means unlock.
3
Channel Lock determining that when user
wish to play the lock channels, whether
have to input the password or not. If the
setting is “Yes”, play the channels with lock
mark will show up a dialogue on the screen
and ask for the password. If the setting of
“Channel Lock ”is “No”, the Lock function
will invalid.
4
New Password is used for revising
password; you can input the new password
in this item by using number keys directly.
After you filled in 4 digital numbers, the
highlight will auto skip to Confirm
Password and ask you to input the new
password again. If the password is correct,
the screen will show up a message of
“Saving Data, Please Wait…”. After finish
saving and draw back to “System Setup”
menu, the revising is complete.
5
Press[Exit] key to draw back from the
“Parental Lock” menu.
Menu Operations
19
8. Tools
When you enter to “Tools” menu, you will see a
screen like below:
In “Tools” menu:
1
Press[Volume Up/Volume Down]key to
select menu pages among Channel,
Installation, System and Tools.
2
Press[Channel Up/Channel Down]key to
select menu items among Information,
Satellite Guide, Game, Default Value,
Software Upgrade, SatcoDX Auto
Programming and Help
3
Press[OK]key to enter the selected item.
8.1 Information
1
When you enter to “Information” menu, you
will see a screen like above. The screen
displays software and hardware information.
2
Press[Exit] key to draw back from “Tools”
menu.
8.2 Satellite Guide
When you enter to “Satellite Guide” menu, you
will see the screen like below:
“Satellite Guide” is use for user to enter local
longitude; local latitude and satellite longitude.
By the evaluation from the receiver evaluate the
antenna azimuth and antenna elevation; user
can follow this guidance to adjust antenna.
1
You can use number keys to input
parameters in “Local Longitude”, “Local
Latitude” and “Satellite Longitude”.
2
You can use [Left/Right]key to select east
or west in “Local Longitude” and “Satellite
Longitude” ,select north and south in
“Local Latitude”.
3
Moving highlight to “Start” item and
press[OK]key. The lower column on the
screen will calculate the corresponding
value automatically.
4
Orientation means the angle between
south and satellite.
5
Press[Exit]key to draw back to “Tools”
menu.
Menu Operations
20
8.3 Default Value
Default Value:
When you press[OK]key In the “Default
Value” item:
1
There will pop a dialogue for you to enter
the password, and the default password
is “0000”.
2
After you input the correct password,
there will show a warning message to
inquiry you “The operation will load
default and erase all the channels that
user added, continue?”.
3
If you select “Yes” option, the all revised
parameters of the receiver will reset to
default value. Please carefully to using
this function.
4
In step 1 and step 2, press[Exit]key can
draw back from this item and without
saving.
Delete All Channel:
When you press [OK] key in the “Delete All
Channel” item, it will pop a dialogue ask you
whether confirm to delete all channel. If you
select “Yes”, all the channel will be deleted.
8.4 Software Upgrade
Upgrade by RS232:
1
We offer the functions for user to connecting
receiver (Master) to the other receiver
(Slave) via serial interface.
Menu Operations
21
2
Connect master receiver to slave receiver
via serial interface. Enter “Software
Upgrade” menu in master receiver and
press[Volume Up/Volume Down]keys to
switch upgrade mode.
Upgrade modes include: code / Program
List / user back /video back / radioback /
defaultdb / code + program list.
3
Turn on slave receiver and it needn’t operate
any setting.
4
Moving highlight to “Start” on master reeciver
and press[OK]key to start upgrade.
5
Press [Exit]key to save the parameters and
draw back.
Menu Operations
22
9. Game
When you enter “Game” menu, you will see
three Games include Tetris, Snake and Othello.
Basic operation statement:
9.1 Tetris
Moving highlight to “Setup” and
press[Volume Up/Volume Down]key to
select the game level (speed).
Moving highlight to “Start” and
press[OK]key to start the game.
Moving highlight to[Cancel]keys and
press [OK]key to draw back from the
game.
Start on the game:
[Volume Up/Volume Down] Move
shape left or right
Channel Up” Rotate clockwise
Channel Down” Faster drop
[OK] Pause/Play the game
[Exit] Quit game and draw back to
“Game” menu.
9.2 Snake
Moving highlight to “Setup” and
press[Volume Up/Volume Down]key to
select the game level (speed).
Moving highlight to “Start” and
press[OK]key to start the game.
Moving highlight to[Cancel]keys and
press [OK]key to draw back from the
game.
Start on the game:
[Volume Up/Volume Down/Channel
UP/Channel Down] use these arrow
keys to guide the snake.
[OK] Pause/Play game
[Exit] Quit game and draw back to
“Game” menu.
9.3 Othello
Moving highlight to “Setup” and
press[Volume Up/Volume Down]keys
to select the game level (degree of
difficulty).
Moving highlight to “Start” and
press[OK]key to start the game.
Moving highlight to[Cancel]keys and
press [OK]key to draw back from the
game.
Start on the game:
[Volume Up/Volume Down/Channel
UP/Channel Down] use these arrow
keys to guide chessman.
[OK] set chessman.
[Exit] Quit game and draw back to
“Game” menu.
Trouble Shooting
23
10. Trouble Shooting
If you suspect there is a fault with your receiver, please check the following trouble shooting guide
before calling authorized service agent.
Warning! Under no circumstances attempt to repair the receiver yourself. Tampering with the
receiver
may result in fatal electric shock and will invalidate your warranty.
Symptom
Possible cause
Settings you made in the
menu have not change
The receiver lost power before being able
to enter into standby mode
Some of the Settings saved by user can be
deleted partly or fully
No signal The level of signal is weak
LNB is out of order
The cable from the LNB is incorrectly
connected(short circuit or open circuit)
The position of dish is aligned incorrectly
Receiver is on but no picture
or sound except the following
messages (NO TV program)
Channel is not available
Channel is scramble
Receiver not responding to
remote control unit
RCU batteries are dead or inserted
incorrectly
The RCU is pointing toward wrong
direction
poor picture Quality The level of Signal strength is low
No sound RCA cable is connected incorrectly
The Volume level is low
Muting function is active
No display on the LED Display
Panel
The power cord is not plugged in correctly.
No picture on the screen Receiver is in Standby mode
RCA Jack is not connected firmly to the
video output port of television
Incorrect channel or video output is
selected on television
Brightness level of your TV set is
incorrectly defined
Specifications
24
11. Specifications
11.1 General
System standard Fully MPEGII/DVB Compliant
Channel Storage Max.4000 TV and Radio Channels
Input Frequency 950~2150Mhz
RF Input level -65~-25dBm
LNB Control DiSEqC1.0/1.2
LNB Power 13V/18V (Max,500mA)
LNB tone switch 22KHZ
Waveform QPSK(SCPC,MCPC capable)
Symbol rate 2~45Mbps
11.2 A/V Mode
Video format MPEG-II Main profile/Main level
Audio format MPEG-II layer I&II
Aspect Ratio 16:9, 4:3
Audio sampling rate 32,44.1 , 48kHz
Audio Type Mono Dual Mono, Stereo, Joint stereo
Graphic display 720x576(PAL), 720x480(NTSC)
11.3 Microprocessor & Memories
Processor 200 MIPS based CPU
RAM 64Mbits
FLASH 16Mbits
11.4 Power & Environment Condition
Supply Voltage Free Voltage(100~250V AC, 50/60Hz)
Supply Power Max.20W
Operating temp 5~45
11.5 Physical Specification
LED display 4Digits
Weight 2.0Kg
Dimensions 220(W) x 153(D) x 49(H)mm
11.6 Connection
Satellite IF input F-type(Digital)
Satellite IF loop out 950-2150MHz
RS232 9 way D Rs232 DCE serial port
Scart TV
Video Composite Video I/O,RGB,CVBS
Audio Audio left
Audio right
Control Output 0/12V out
Modulator UHF CH 21-69 Adjustable(Option)
Specifications subject to change without notice.
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Golden interstar Big Sat BS-S 67 CR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Golden interstar Big Sat BS-S 67 CR in the language / languages: English as an attachment in your email.

The manual is 1,59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info