708921
9
Zoom out
Zoom in
Previous page
1/13
Next page
- 22 -
Setting <Multi>
1 stroboscopic flash.
Long press the <MODE>
button for 2 seconds so that
<Multi> is displayed. Long
press the <MODE> button
for 2 seconds again to exit.
7. M: Wireless Flash Shooting with Manual Flash
This describes wireless (multiple shooting) using manual flash. You
can shoot with a different flash output setting for each slave unit
(firing group). Set all parameters on the master unit.
Setting the flash mode to
1 <M>
Press the <MODE> Button
to set the flash to M mode.
Setting flash output
2
Turn the Select Dial to set
the flash output of the
groups.
Taking the picture
3
Each group fires at the set
flash ratio.
Using a flash (master/slave) with a radio transmission wireless
shooting function make it easy to shoot with advanced wireless
multiple flash lighting, in the same way as TTL autoflash shooting.
The basic relative position and operation range are as shown in the
picture. You can then perform wireless TTL autoflash shooting just
by setting the master unit to <TTL>.
8. Multi: Wireless Flash Shooting with Manual
Flash
Setting flash output/flash
2 frequency/flash times.
Setting the flash
output/flash frequency/flash
times in the A group. Setting
the multi flash mode. (see
Page35 )
B and C group can only
control the ON/OFF of the
slave unit by pressing the
<MODE> Button.
Transmission distance is about 30m.
● Use the supplied mini stand to position the slave unit.
● Before shooting, perform a test flash and test shooting.
● The transmission distance might be shorter depending on the
conditions such as positioning of slave units, the surrounding
environment and whether conditions.
You can divide the slave units into two or three groups and perform
TTL autoflash while changing the flash ratio (factor). In addition, you
can set and shoot with a different flash mode for each firing group,
for up to 3 groups.
Wireless Multiple Flash Shooting
Auto Shooting with Two Slave Groups
Slave/Master Unit's Positioning and Operation Range
Autoflash Shooting with One Slave Unit
A
B
A
B
C
Auto Shooting with Three Slave Groups
- 39 -
- 40 -
MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET
MODE ZOOM SYNC SLAVE
SET
1. Disturbed by the 2.4G signal in outer environment (e.g. wireless base
station, 2.4G wifi router, Bluetooth, etc.)
  → To adjust the channel CH setting on the flash trigger (add 10+ channels) and
  use the channel which is not disturbed. Or turn off the other 2.4G equipment
  in working.
2. Please make sure that whether the flash has finished its recycle or caught up
with the continuous shooting speed or not(the flash ready indicator is lighten)
and the flash is not under the state of over-heat protection or other abnormal
situation.
Please downgrade the flash power output. If the flash is in TTL mode, please
  try to change it to M mode(a preflash is needed in TTL mode).
The Reason & Solution of Not Triggering in Godox 2.4G Wireless
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Godox Speedlite TT350 Canon at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Godox Speedlite TT350 Canon in the language / languages: English as an attachment in your email.

The manual is 2,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info