656125
3
Zoom out
Zoom in
Previous page
1/4
Next page
1.Power Supply
Three power supply modes are available:
2.Installing the Video Light
Screw the Locking Ring (12) to the highest point
and insert the Camera Hotshoe Connection (13)
horizontally into the hotshoe of a camera or a
camcorder.
Tighten the Locking Ring (12).
Note: If your camcorder has no hotshoe connection, you
are advised to purchase a connecting bracket for
camcorder. The video light has a 1/4″ Bracket Mounting
Hole as your camcorder does. Therefore, you can easily
connect both the light and the camcorder to the bracket.
* When using AA batteries or lithium battery, the Battery Level
Indicator (05) turns green, meaning battery power is sufficient.
When the indicator turns red, the battery power is low.
* When the indicator turns red and blinks, the lithium battery
power is low. Please recharge it immediately before use in
order to avoid forceful auto off.
* When using DC power supply, the indicator shows green.
Using batteries: This
light uses AA-sized
alkaline or Ni-MH
rechargeable batteries.
Using lithium battery:
This light uses SONY
NP-F970 model lithium
battery.
Using DC power jack:
This light can be powered
by DC power supply. Use
an adapter (purchased
separately) to connect the
light with the AC power
supply. LED126 uses a
6V-9V adapter and
LED170 uses a 6-12V
adapter.
3.Using the Video Light
Turn the Battery
Compartment Lock (07)
down and at the same
time push the Battery
Compartment (08) to the
left and open it.
Install AA batteries
according to indications
in the compartment and
then lock it.
Switch the power on,
the video light giving out
light.
Turn the Brightness
Controller (04) to adjust
the brightness.
By operating the Angle
Adjusting Knob A and B,
you can change the
LED illumination
direction.
Instead of AA batteries,
the light can be powered
by DC power supply.
Use an adapter
(purchased separately)
to connect the light with
the AC power supply.
LED126 uses a 6V-9V
adapter and LED170
uses a 6-12V adapter.
After using the light, please power it off.
Installation and Operation
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Godox LED170 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Godox LED170 in the language / languages: English as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info