636440
15
Zoom out
Zoom in
Previous page
1/27
Next page
14
of signal or LNB your receiver is connected
to. Press BLUE button, it will automatically
detect DiSEqC connecting and set the right
configuration of LNB as well. In less than 1
minute, it will show you the connecting
status, you just need to press OK button to
scan the connected satellites if any.
C. Edit
Press GREEN button to enter next main
part: “Edit Satellite” menu.
D. TP
Press YELLOW button to enter next main
part: “Transponder” menu.
Edit Satellite
The menu displays as the following:
- Satellite setup menu
- Indication picture for the connecting of
antenna and DiSEqC switcher, Motorized
system.
We supply the following functions:
1. Press RED button to scan certain satellite
2. Press GREEN button to enter keyboard
menu to rename certain satellite
3. Press BLUE button to enter “Auto DiSEqC
menu to check your dish connecting
4. Setup satellite’s parameters as the
following:
- Satellite: Remand certain satellite by using
GREEN button;
- Longitude: The angle of satellite’s
longitude is can not be changed;
- TP: Select the TP of certain satellite. Press
OK button to select one from the list or
press LEFT/RIGHT button to switch one by
one
- LNB: Select the LNB (value & type) on
antenna. Press OK button to select one
from the list or press LEFT/RIGHT button to
switch one by one
Notice: When you select Uni. (9750
/10600), both 9750 and 10600MHz are
supported at the same time, the 22KHz
Tone setting is unnecessary(disabled),
because high or low band is selected by
22KHz automatically
- 22KHz: Press OK or LEFT/RIGHT to turn
22KHz Tone switcher on or off.
Notice: When you use a dual LNB or two
antennas connected to a 22KHz Tone
switch box, make 22KHz Tone switch on or
off to select LNB or antenna.
- 12V: Press OK or LEFT/RIGHT to turn 12V
switcher on or off
- DiSEqC 1.0/1.1: According to the option
and position of DiSEqC switcher, select
OFF(disabled), DiSEqC A to D by OK or
LEFT/RIGHT button, it supports up to 16
antennas connected to the receiver at the
same time.
- Motor: Press OK or LEFT/RIGHT to set
motor on or off; press YELLOW button to
enter “Motor” menu
Motor Menu:
a) Motor Type
Press LEFT/RIGHT button, you can
select DiSEqC1.2 or USALS
(DiSEqC1.3), according to the
motorized DiSEqC system you are
using.
b) Satellite
Select a satellite name that can be used
to identify a motor position by pressing
OK or LEFT/RIGHT button. The
longitude of current satellite will be
shown too.
c) TP
Press OK or LEFT/RIGHT button, you
can select one transponder from current
transponder list to locate the signal.
d) Setup Motor
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Globo OPTICUM 4000TSCR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Globo OPTICUM 4000TSCR in the language / languages: English as an attachment in your email.

The manual is 6,48 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Globo OPTICUM 4000TSCR

Globo OPTICUM 4000TSCR User Manual - German - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info