814087
13
Zoom out
Zoom in
Previous page
1/16
Next page
20.
Stove in use
After the flue gas temperature has reached and gone beyond the level required
during a certain programmed time, the stove will switch to the users mode which is
normal use. The display will show 'work' and the ON/OFF light is burning. The
capacity can be regulated by pressing the (P2) button and the room temperature
by pressing the (P1) button. As soon as the flue gas temperature has been
reached the air fan will be switched on.
Important: At this stage, after a required time is set, the oven will clean the
fire grate. 'Fire grate' will appear in the display (cleaning fire grate), the auger
is switched on (LED- auger on) the smoke extractor fan is also working at
the given speed. After the given time the stove switches back to the user's
mode.
Changing the set heating capacity
During normal use of the stove the heating capacity can be changed by pressing
the P2 button. (LED capacity setting is on). To raise the heating capacity press
(P2) once again. To lower the capacity press P1. The chosen capacity will appear
on the display. To complete the setting, wait 5 seconds without touching the control
panel or pressing P3. The heating capacity levels range from PT 1 to POT 5. POT1
is the lowest level. POT5 is the highest level. The stove switches automatically
between the lower and higher capacity levels.
Changing the set room temperature
To change the room temperature press (P1). The display will show the set room
temperature (Programme temperature). The temperature can be changed by
pressing (P1) and (P2) buttons. After 5 seconds this given temperature will be
stored and the display will return to its normal position. (P3 can be pressed to exit.
21.
The set room temperature is reached
(Temperature programme)
Once room temperature has been reached the heating capacity of the stove is
automatically set to the minimum requirement. In this situation the display shows
'modulation'. When the room temperature drops below the set temperature, the
stove returns to the mode 'work' and to earlier settings.
Standby
If activated in the menu the STANDBY setting will switch off the stove when all the
following conditions have been met. Standby will be carried out when the room
temperature becomes higher than the programmed temperature plus a limited
tolerance.
The display will show 'Go STBY' followed by the remaining minutes. After a
certain time the display will show 'Wait for cooling' (Cooling mode). In this
situation the auger will be switched off, the fan will stop when the programmed
level has been reached and the LED will flash ON/OFF. As soon as the flue gas
temperature has reached the programmed temperature the stove will switch to
STANDBY and the display will show 'STOP ECO TEMP GOOG'. The auger is
switched off (LEDS- auger off) the air fan is switched off and also the smoke
extraction. When the room temperature drops below the programmed
temperature the stove will switch back on.
Switching off the stove
To switch off the stove simply press (P3). The display will show 'End cleaning'.
The auger engine will be switched off (LEDS- auger off), the speed of the smoke
extractor is set and the (LED ON/OFF) flashes. The air fan remains on until the
exhaust gas temperature is below the programmed temperature. When the flue
gas temperature is below the programmed temperature the stove will be switched
of and 'OFF' will appear in the display.
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Globe Fire Jacobus at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Globe Fire Jacobus in the language / languages: English as an attachment in your email.

The manual is 1.8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Globe Fire Jacobus

Globe Fire Jacobus User Manual - German - 16 pages

Globe Fire Jacobus User Manual - Dutch - 16 pages

Globe Fire Jacobus User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info