607008
3
Zoom out
Zoom in
Previous page
1/8
Next page
Mounting and
Operating Instructions
Flush-mounted outdoor station
with call push button 1-gang
1260 65/66/67
1271 65/66/67
Flush-mounted outdoor station
with call push button 3-gang
1261 65/66/67
1272 65/66/67
2
Device description
The flush-mounted outdoor station is part
of the Gira door communication system.
The basic structure of a flush-mounted
outdoor station is presented in the
example of the flush-mounted outdoor
station with call push button 3-gang:
1 Door communication bus coupler
2 Audio connection cable
3 Speech insert
4 TX_44 frame bottom section
(not in scope of supply)
5 Door speaker top unit
6 TX_44 frame top section
(not in scope of supply)
7 Call push button covers
8 Call push button 3-gang
3 4 5 6
2 1 8 7
3
Mounting
The flush-mounted outdoor station is
installed in two common flush-mounted
panel boxes:
1. Connect the door communication bus
coupler to
the 2-wire bus on the BUS terminals
if necessary, the wires of the additional
supply to the "ZV" terminals
if necessary, the wires of a mechanical
bell button to the "ET" terminals.
2. Insert the audio connection cable into
one of the two system connectors of
the bus coupler.
3. Guide the audio connection cable to the
upper flush-mounted panel box and ins-
tall the bus coupler in the lower flush-
mounted panel box.
Attention
Installation and mounting of electrical
devices may only be carried out by a
qualified electrician.
Do not use the sealing rings included
with the TX_44 frame when installing
flush-mounted inserts.
i
Deactivating call push button
illumination
To deactivate the call push button illumi-
nation continuously, remove the jumpers
between BUS and ZV.
4
4. Insert the audio connection cable into
one of the two system connectors of
the speech insert.
5. Install the speech insert.
6. Place the bottom section of the TX_44
cover frame in place and attach the call
push button and the speech insert to
the flush-mounted inserts.
7. Clip on the frame top section and press
in the Torx screws.
Start-up
Once all of the devices (outdoor and home
stations, control unit etc.) have been
installed, you can start up the door com-
munication system. Start-up is described
in the system manual included with the
control unit.
Operation
Initiating a call (ringing)
Press the call push button to trigger a call
tone at the assigned home station. The
button press is confirmed by an additional
acknowledgement tone.
Switching light on/off
(in conjunction with a switching
actuator)
Press the call push button to switch on
light or another device via an assigned
switching actuator. The button press is
confirmed by an additional acknowledge-
ment tone.
5
Volume setting
The volume can be set separately at each
outdoor station.
The volume setting must be made by two
people.
1. Start programming mode at the control
unit by pressing the "Systemprogr."
button for 3 seconds until the yellow
LED next to the button starts flashing.
2. Briefly press a previously assigned call
push button at the outdoor station.
3. The second person accepts the door
call at the home- station (via receiver
or speech button) and starts speaking.
4. Briefly press the call push button at the
outdoor station again.
The volume changes when the button
is pressed during the voice connection.
There are five volume levels in total. The
next-highest volume is set with each
button press. When the loudest level is
reached, the next button press sets the
quietest volume level.
5. End the voice connection.
The most recently set volume level is
saved in the outdoor station.
6. Exit programming mode at the control
unit by briefly pressing the "System-
progr." button.
6
Changing the label plates
To change the label plates, the call push
button cover can simply be lifted up.
1. Carefully lift up the call push button
cover, e.g. with a screwdriver.
2. Change the label plate.
3. Replace the call push button cover and
press on it firmly.
Suitable label plates can be obtained with
the optional Gira labelling software and
the appropriate Gira labelling sheets.
7
Acceptance of guarantee
The warranty is provided in accordance
with statutory requirements via the spe-
cialist trade.
Please submit or send faulty devices post-
age paid together with an error description
to your responsible salesperson (specialist
trade/installation company/electrical spe-
cialist trade).
They will forward the devices to the
Gira Service Center.
Gira
Giersiepen GmbH & Co. KG
Elektro-Installations-
Systeme
Postfach 1220
42461 Radevormwald
Deutschland
Tel +49 (0) 21 95 / 602 - 0
Fax +49 (0) 21 95 / 602 - 191
www.gira.de
info@gira.de
10 41 03 70 22/11
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gira 1271 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gira 1271 in the language / languages: English as an attachment in your email.

The manual is 0,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gira 1271

Gira 1271 Usermanual and installation guide - Dutch - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info