580058
29
Zoom out
Zoom in
Previous page
1/40
Next page
27
Gigaset A540-A540A / en / A31008-M2601-L101-2-7619 / appendix.fm / 28.10.2014
A-Klasse_Layout_Neu, Version 4, 28.05.2014
Manufacturer's advice
"Base" flashes on the display.
The handset is outside the range of the base: ¤ Move the handset closer to the base.
The base is not switched on: ¤ Check the base power adapter.
The base's range has decreased because Max. Range is deactivated: ¤ Activate Max. Range (¢ page 19)
or ¤ reduce the distance from handset to base.
"Register handset" or "Place handset into base" flashes on the display.
The handset has not yet been registered or was de-registered due to the registration of an additional
handset (more than 4 DECT registrations):
¤ Register the handset again (¢ page 7, ¢ page 20).
The handset does not ring.
The ringtone is deactivated: ¤ Activate ringtone (¢ page 23).
The phone does not ring if the caller has withheld his/her number: ¤ Activate the ringtone for anonymous
calls
(¢ page 24).
The telephone does not ring during a specific time period: ¤ Check the time control for external calls
(¢ page 24).
No ringtone/dial tone from the fixed line network.
The telephone cable supplied has not been used or has been replaced by a new cable with the wrong pin
connections:
¤ Please always use the telephone cord supplied or ensure that the pin connections are
correct when purchasing from a retailer
(¢ page 32).
The connection always terminates after approx. 30 seconds.
A repeater (earlier than version 2.0) has been activated or deactivated (¢ page 21): ¤ Switch the handset
off and back on again (¢ page 8).
Error tone sounds after system PIN prompt.
The system PIN you have entered is incorrect: ¤ Repeat the procedure, reset the system PIN to 0000 if
necessary
(¢ page 25).
Forgotten system PIN.
¤ Reset the system PIN to 0000 (¢ page 25).
The other caller cannot hear you.
The handset is "muted": ¤ Reactivate the microphone (¢ page 11).
The caller's number is not displayed.
Calling Line Identification (CLI) is not approved for the caller: ¤ Caller should ask the network provider to
enable Calling Line Identification (CLI).
Calling Line Identification Presentation (CLIP) is not supported or approved by the network provider: ¤
Caller display (CLIP) must be enabled by the network provider.
The telephone is connected via a PABX or a router with an integrated PABX (gateway) that does not transmit
all information:
¤ Reset the system: Briefly pull out the power plug. Reinsert the plug and wait until the device restarts.
¤ Check the settings on the PABX and activate telephone number display, if necessary. To do this, search
for terms such as CLIP, calling line identification, telephone number identification, caller ID, etc. in the user
guide of the system or ask the system manufacturer.
Error tone with keypad entries.
Action has failed/invalid input: ¤ Repeat the procedure . . . Read the display and refer to the user guide if
necessary.
The messages on the network mailbox cannot be listened.
The PABX is set to pulse dialling: ¤ Set the PABX to tone dialling (¢ page 22).
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gigaset A540A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gigaset A540A in the language / languages: English as an attachment in your email.

The manual is 2,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gigaset A540A

Gigaset A540A User Manual - German - 40 pages

Gigaset A540A User Manual - Dutch - 40 pages

Gigaset A540A User Manual - French - 41 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info