580056
37
Zoom out
Zoom in
Previous page
1/47
Next page
35
Service (Customer Care)
Gigaset A510H / IM1 en / A31008-M2252-R101-2-4N19 / appendix.fm / 28.07.2011
Version 4.1, 21.11.2007
Questions and answers
If you have any queries about the use of your
telephone, visit our website at
www.gigaset.com/service
for assistance 24/7.
The table below also lists steps for trouble-
shooting.
Authorisation
This device is intended for use within the
European Economic Area and Switzerland. If
used in other countries, it must first be
approved nationally in the country in ques-
tion.
Country-specific requirements have been
taken into consideration.
We, Gigaset Communications GmbH,
declare that this device meets the essential
requirements and other relevant regulations
laid down in Directive 1999/5/EC.
A copy of the 1999/5/EC Declaration of Con-
formity is available at this Internet address:
www.gigaset.com/docs
The display is blank.
1. The handset is not activated.
¥ Press and hold the end call key a.
2. The battery is empty.
¥ Charge the battery or replace it
(¢ page 10).
"Base" flashes on the display.
1. The handset is outside the range of the base.
¥ Move the handset closer to the base.
2. The base's range is reduced because Eco
Mode is activated.
¥ Deactivate Eco Mode (¢ page 30) or
reduce the distance between the handset
and the base.
3. The base is not activated.
¥ Check the base power adapter.
4. Handset has not been registered with the
base or has been de-registered.
¥ Register the handset (¢ page 13).
The handset does not ring.
1. The ringtone is switched off.
¥ Activate the ringtone (¢ page 33).
2. The phone only rings if the phone number has
been transferred.
¥ Activate the ringtone for anonymous calls
(¢ page 32).
The connection always terminates after
approx. 30 seconds.
Repeater activated/deactivated.
¥ Activate/deactivate the handset (¢ page 19).
The other party cannot hear you.
You pressed the mute key v during a call. The
handset is "muted".
¥ Unmute the microphone (¢ page 24).
The number of the caller is not displayed
although CLIP has been set.
Calling Line Identification is not enabled.
¥ The caller should ask the network provider to
enable Calling Line Identification (CLI).
You hear an error tone when keying an input.
Action has failed/invalid input.
¥ Repeat the process.
Watch the display and refer to the user man-
ual if necessary.
Exclusion of liability
Some displays may contain pixels (pic-
ture elements), which remain activated or
deactivated. This is completely normal
and does not indicate a fault.
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Gigaset A510H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Gigaset A510H in the language / languages: English as an attachment in your email.

The manual is 1,07 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Gigaset A510H

Gigaset A510H User Manual - German - 47 pages

Gigaset A510H User Manual - Dutch - 48 pages

Gigaset A510H User Manual - French - 49 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info