643439

GGM Gastro HV865 Noah Manual

18
Zoom out
Zoom in
Previous page
1/24
Next page
18/24
12.1.3. HOLD PHASE
To set the hold phase, press the TIME key to select a temperature cycle. The time can be set to the
following values, "Hold", "InF" (infinite time) and from 00:00 to 24:00 hh:mm. Select the "Hold" value.
The display DISPA1 shows the temperature setpoint value of the hold phase, which is equal to
parameter r21. This value cannot be modified. To stop the hold phase, press the START/STOP key for
one second. During the Hold phase there is a cyclic humidification of 20%.
12.1.4. DELETING A PHASE
To delete a phase, select the phase and press the ON/OFF key for 4 seconds. Repeat the
procedure for all the phases to free a program.
12.2. COOKING VIA PROGRAM
Press the PROGRAMMES key, select the programme number and press the START/STOP key to start the
cycle. Displays DISPC1 and DISPB1 show P xy where xy is the number of the programme in progress. If
the programme consists of several phases, at the end of each phase, the buzzer will sound continuously for
1 sec.
12.3. MODIFICATIONS DURING THE COOKING PHASE
Temporary modifications can be made during program cooking as in the manual cycles (the new values are
kept in case of power failure, but they are not saved as new settings for the program in progress).
13. QUICK COOLING OF THE COOKING CHAMBER
Press the PROGRAMS key. The display PROGRAMS shows the number of the first program (P01). Use the
DOWN key to select the COOL program and confirm by pressing the PROGRAMS key.
The setpoint value shown is equal to the temperature value of the chamber decreased of r14. The setpoint can
vary in the interval.
To start the cooling cycle, configure the setpoint and make sure that the door is open. Press the START/STOP
button.
The fans are activated.
If the door is closed, the cooling cycle is not started
The cooling phase stops as soon as the door is closed.
Once the configured setpoint is reached, the fans turn off and the buzzer activates for a time equal to 15s. The
sound of the buzzer is intermittent with f= 1Hz.
Display DISPB1 shows the "door" label, Display DISPB2 scrolls the COOL label.
Stop the cooling phase by pressing START/STOP.
14. CHAMBER HEATING OPERATION
The temperature control is managed via the two outputs HEATING ELEMENTS 1 and HEATING ELEMENTS 2.
Until the first set point is reached both are on.
Subsequently, the T temperature of the chamber, applies as below
STATUS
HEATING
ELEMENTS 1
HEATING
ELEMENTS 2
T < SETPOINT - 5
ON
ON
SETPOINT - 5 < T< SETPOINT
OFF
ON
T > SETPOINT
OFF
CYCLIC
… 18 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for GGM Gastro HV865 Noah at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of GGM Gastro HV865 Noah in the language / languages: English as an attachment in your email.

The manual is 0,64 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info